WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Chevrolet Tahoe

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1771 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
PIT5288E2017-08-15. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC); VISIBILITY; STEERING; TIRES; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
PIT5434A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SEATS. This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
PIT5389B2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC5932A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIE03652017-08-15. Service bulletin. ELECTRICAL SYSTEM. This engineering information bulletin is requesting information from the dealers on a customer concern that one of the USB ports is not charging, allowing data to transfer.
PI0592D2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides information on service programming system (SPS) errors.
09-06-04-026M2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
PIT5444C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:IGNITION; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the “i” icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
PIP5411D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:MOUNTING. This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition. Dealer directed to follow latest version of PIP5507 if the fuel pump does not correct the concern.
PIT5308B2017-08-15. Service bulletin. STRUCTURE:BODY:HATCHBACK/LIFTGATE; ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.
PIT5564A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.
17-NA-1422017-08-15. Service bulletin. ELECTRICAL SYSTEM. This informational bulletin provides information on Wireless Charging Module Diagnosis.
15-06-03-002F2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT. This informational bulletin provides information on approved warranty part numbers for original equipment batteries
03-06-03-004U2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIT5236G2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
PIT5438B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
PIC61872017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that some vehicles intermittently the favorites saved from a USB drive or SD card are grayed out and not selectable. Please communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
PIT5391A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position, Any of the following Diagnostic Trouble Codes may be set: B1370, B1325, P0650, P263A, P263B, P0513, and/or P0262B. Trucks equipped with 4WD may have a Service 4WD message and Diagnostic Trouble Codes C0364 and/or U0403 may set. Also the sound of a relay clicking while driving or engine stays running with ignition off until door is opened. Technician will inspect all the under-hood fuse block-X50A connectors for any backed out terminals, poor terminal fit and/or bent/twisted terminals. The most common terminals with these issues have been with terminal M5 at connector X4, for circuit 5199 and terminal M7 at connector X2, for circuit 439. Technician will inspect for any backed out terminals, poor terminal fit and/or bent/twisted terminals at the left instrument panel fuse block - X51L. The most common terminals with these issues have been terminal 42 at connector X1, for circuit 5199 and terminal 44 at connector X2, for circuit 1850. Also circuit 5199 will need to be inspected and repaired under the driver?s sill plate.
PIT5206D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.
PIT55002017-08-15. Service bulletin. ELECTRICAL SYSTEM:WIRING; SEATS; SEAT BELTS. This Preliminary Information communication provides information to the technician about the vehicles equipped with power folding 3rd row seat and how to diagnosis and repair seats that do not fold down completely or the 60% side does not fold even with the 40% side. Technician will inspect under the 3rd row seat for any objects that will prevent the seat from folding as designed. If the center seat belt from the roof is connected to the seat belt buckle or any of the seat belt buckles not properly stowed in the seat cushion pockets this will prevent the seat from properly folding. Also check under the 60% seat for the wire harness routing. If the harness is not routed correctly or seat connector is not properly attached to the seat bracket the seat will not fold down correctly. If the wire harness or connector is found out of place, reroute the seat harness or use a zip tie for the connector to the bracket. If the concern is still present remove the two rubber bumpers form the 60% seat side rails. After removing the rubber bumpers install a piece of Kent Automotive BRS Flocking tape P/N KT13487, or equivalent, in place of the rubber bumper.
PIC61832017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician to help diagnose vehicles that may have a radio inoperative. This concern will last through multiple ignition cycles and is not intermittent. If Service Information diagnostics do not point to the Media Disc Player as being at fault, please continue with normal diagnostics. If SI diagnostics do point to the Media Disc Player being at fault, please do not unplug or remove power from the module or vehicle. Technician will contact General Motors Technical Assistance Center for further assistance.
PIT5232B2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.
PIT5457B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.
PIP5369B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have "Service 4 Wheel Drive" message on the Driver Information Center. Provides the technician with additional information to ensure that the TCCM contains the latest software released to address previous issues, also advises of default action changes. Calls out specific circuits to be inspected to help isolate intermittent codes.
11-08-49-001O2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM. This technical bulletin provides repair procedure information to correct a customer concern of Transport Mode On message displayed in Driver Information Center (DIC) and/or battery light is flashing.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.