WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Tahoe

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2584 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIT5277D2018-02-21. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show “No Audio” in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
PIT5233D2018-02-21. Service bulletin. WHEELS; SEAT BELTS; ELECTRICAL SYSTEM; STEERING; SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP5446A2018-02-21. Service bulletin. BACK OVER PREVENTION. This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
PIP5540A2018-02-21. Service bulletin. ENGINE. This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5330C2018-02-21. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIP5308B2018-02-21. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE; EXTERIOR LIGHTING. This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon Malfunction Indicator Lamp on. Technician should follow published Service Information diagnostics that will lead to an oil pump replacement. Technician should replace the oil pump. If debris is found, the main and rod bearings should be inspected before engine replacement is considered.
PIT5245C2018-02-21. Service bulletin. ENGINE AND ENGINE COOLING; COMMUNICATION. This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
PIP5130J2018-02-21. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
PIT5552A2018-02-21. Service bulletin. COMMUNICATION; BACK OVER PREVENTION: CAMERA SYSTEM. This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
PIP55402018-02-21. Service bulletin. EQUIPMENT. This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIP5252B2018-02-21. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
PIT54682018-01-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
PIT5444A2018-01-22. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician with tips on the Text Messaging feature that is available on some newer General Motors infotainment systems.
PIC6085A2018-01-22. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
PIT54652018-01-22. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT54642018-01-22. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP53302018-01-22. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
PIT54662018-01-22. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician to help converting vehicles to fleet key option Regular Production Option Code 6E2 or 6E8. Technician will need to check the Regular Production Option Code for 6E2 or 6E8. Technician will need to order the correct key part number per the Regular Production Option Code. Then the technician will need re-code the lock cylinders to match the Regular Production Option Code. Also replace the Body Control Module and normal Service Programming System to the Body Control Module will turn the vehicle to a common key.
PIT5049B2018-01-22. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
PIP53252018-01-22. Service bulletin. FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
PIT5383B2018-01-22. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Preliminary Information communication provides information to the technician about vehicles that have various Heater-Vent-Air Conditioning issues. Technician should use Tis2Web to reprogram the Heater-Vent-Air Conditioning control module.
PIT5277B2018-01-22. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show ?No Audio? in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
PIT5448B2018-01-22. Service bulletin. ENGINE. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
PIP5250G2018-01-22. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NPO, NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 reprogram the transfer case control module with the latest calibration from TIS2WEB and perform the setup procedure.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.