Service bulletins for the 2013 Chevrolet Tahoe
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1803 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Brakes are shown. Show all
| 99-04-20-002I | 2017-08-15. Service bulletin. PARKING BRAKE:DRIVELINE. This informational bulletin explains a normal condition for what and how the drive line can clunk. |
|---|---|
| PIT5206D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205. |
| PIT4597E | 2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides the technician with the additional steps that are needed to help perform a successful brake bleed on the 2-Mode Hybrid with Regular Production Option Code HP2. With a battery maintainer installed on the vehicle use brake pressure bleeder that maintains 30 psi for the entire bleed procedure. |
| 00-05-22-002O | 2017-08-15. Service bulletin. SERVICE BRAKES. This informational bulletin provides technicians with a brake lathe calibration procedure. |
| PI1360A | 2017-08-15. Service bulletin. PARKING BRAKE; PARKING BRAKE:DRIVELINE:HYDRAULIC:ACTUATOR. This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park or vehicle rolls in park or park will not hold. |
| 06-00-89-026L | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| PIT5206 | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ELECTRICAL SYSTEM; SERVICE BRAKES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. |
| PIT5202 | 2017-08-15. Service bulletin. SERVICE BRAKES; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle. |
| PIP5092 | 2017-08-15. Service bulletin. PARKING BRAKE:DRIVELINE. This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns. |
| PIT4383N | 2017-08-15. Service bulletin. SERVICE BRAKES. This Preliminary Information communication advises the technician that the Electronic Brake Control Module and Brake Pressure Modulator Valve for the 2-Mode Hybrid Utilities and Trucks will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact for further assistance. |
| PIT4593D | 2017-08-15. Service bulletin. SERVICE BRAKES, ELECTRIC; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a lack of brake assist after disconnecting the battery or after the 12 volts battery has run low on voltage. The Antilock Braking System Malfunction Indicator Lamp may also be on. Technician may find Diagnostic Trouble Code C121D sym 00 or C056D sym 00 set in the Electronic Brake Control Module. Technician should be advised to wait for a period of at least 1 minute with the ignition in the "OFF" position prior to disconnecting the negative battery cable. Technician will need to follow these steps to repair the concern. 1. Install the negative battery cable to the battery. 2. Rotate the lever lock clockwise until an audible click is heard in order to connect the negative battery cable to the battery. 3. Position the negative battery cable insulating cover over the negative terminal. 4. Start the vehicle without stepping on the brake pedal. 5. Shut the vehicle "Off" for one minute. 6. Restart vehicle and check brakes for proper operation. 7. Clear codes in the Engine Control Module and the Electronic Brake Control Module. |
| PIT4600E | 2017-08-15. Service bulletin. SERVICE BRAKES, ELECTRIC; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about Electronic Brake Control Module relearn procedure is required anytime the Electronic Brake Control Module is replaced or has been Service Programming System reprogrammed. |
| PIT4907A | 2017-08-15. Service bulletin. SERVICE BRAKES. This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIT4225F | 2017-08-15. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP; SERVICE BRAKES, ELECTRIC. This Preliminary Information communication provides information to the technician about vehicles that have an Antilock Braking System lamp followed by a Service Stability message in the Drivers Information Center. Technician my find Diagnostic Trouble Code C0710 set in the Electronic Brake Control Module. Technician may or may not find Diagnostic Trouble Code C0455. Technician will need to ensure the steering wheel is properly installed to the steering shaft. |
| PIT4208D | 2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC:POWER ASSIST; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID. This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available. |
| PIT4169F | 2017-08-15. Service bulletin. SERVICE BRAKES, ELECTRIC; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have a "Service Stability Message" appears on the Drivers Information Center. Technician will find Diagnostic Trouble Code C0561 set in the Electronic Brake Control Module. Technician will need to address any other Diagnostic Trouble Codes that are set in the vehicle first before working on Diagnostic Trouble Code C0561. |
| PIT5206A | 2017-08-15. Service bulletin. SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages " Brake Pedal Override Feature ", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. |
| PIT5202B | 2017-08-15. Service bulletin. SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle. |
| PIT5206C | 2017-08-15. Service bulletin. SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205. |
| PIT5206B | 2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages "Brake Pedal Override Feature", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. |
| PIP5092A | 2017-08-15. Service bulletin. PARKING BRAKE:DRIVELINE. This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns. |
| PIT4954D | 2017-08-15. Service bulletin. SERVICE BRAKES, AIR:SUPPLY:COMPRESSOR; SUSPENSION. This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up. |
| PIP5175 | 2017-08-15. Service bulletin. PARKING BRAKE; ENGINE AND ENGINE COOLING; WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed. |
| PIT4943C | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIT5206E | 2017-05-22. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; PARKING BRAKE; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES “ BRAKE PEDAL OVERRIDE FEATURE “, TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.