Service bulletins for the 2010 Chevrolet Tahoe
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1601 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| 01-06-01-011I | 2017-12-22. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption. |
|---|---|
| 00-06-01-026H | 2017-12-22. Service bulletin. ENGINE. This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage. |
| PIP4112P | 2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| 09-06-04-026E | 2017-10-12. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2 |
| 10-06-01-008F | 2017-10-12. Service bulletin. ENGINE AND ENGINE COOLING. This technical bulletin provides a procedure to replace the AFM oil deflector, rocker arm cover and clean the carbon deposits for conditons related to Engine Oil Consumption on Aluminum Block/Iron Block Engines with Active Fuel Management |
| PIE0368A | 2017-08-31. Service bulletin. ENGINE AND ENGINE COOLING. This engineering informational bulletin is ending the need for information from the field on vehicles that have a condition of Vehicle Overheating, Noise Originating from Engine Coolant Fans and/or Poor Engine Coolant Fan Performance |
| 17-NA-035 | 2017-08-31. Service bulletin. ENGINE. This technical bulletin provides a procedure to replace the engine cooling fan to correct conditions of the engine cooling fan being inoperative due to moisture within the connector of the fan module. |
| PIP5232B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5258A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0011. If the technician has followed all published Service Information diagnosis and has not come to a conclusion, technician should check the oil pressure at the oil pressure sender. Then the number two cam bearing should be inspected. |
| PIP5069A | 2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a lack of power on initial acceleration from a stop when the ambient temperature is approximately 103 Fahrenheit or greater and may include engine detonation or pre-ignition type events as temperatures approach 120 Fahrenheit. Technician will need to perform published Service Information diagnosis first. If Service Information diagnosis does not isolate the cause of this concern, take a Tech 2 snapshot of the concern happening and note the Spark Parameter in the Ignition Data List. If it drops near/below 0 degrees during the concern, check if there is a cylinder that shows any knock. If there is a knock in any cylinder perform a top engine clean. If the concern is still present, then switching to premium fuel (91 octane or higher) with detergents (Top tier fuel) when ambient temperatures exceed 110 Fahrenheit degrees, this should provide a slight improvement in engine performance when ambient temperatures are high especially as temperatures approach 120 Fahrenheit degrees. |
| PIP5276D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a UPF48R if one is available. |
| PIP5276C | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a PF48 if one is available. If there is no availability of oil filter PF48 use oil filter UPF48R. |
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP5341 | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that engine runs and idles rough. Technician will find P0171 and or P0174. Technician will need to inspect the positive crankcase ventilation tube for a vacuum leak on the left side of the engine. Replace positive crankcase ventilation air tube and cover it with conduit to protect from repeat damage. |
| PIP4404F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5029F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIP5276E | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. Inspect the engine for any oil leaks and repair if need. Technician should change the engine oil and replace the oil filter using a PF48e type filter. |
| PIP5282 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down. |
| PIP5168D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIP4568R | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed. |
| 10-06-01-008L | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE). This technical bulletin provides a procedure to correct the customers concern to replace the left side valve cover and active fuel management oil deflector to reduce oil consumption. |
| 17-NA-035 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. This technical bulletin provides a procedure to replace the engine cooling fan to correct conditions of the engine cooling fan being inoperative due to moisture within the connector of the fan module. |
| PIP4568S | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed. |
| PIP4482C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. This Preliminary Information communication advises the technician of two types of DEX-COOL 50/50 Premix are available through General Motors Service Parts Operations, one with bitterant and one without. Bitterant is a chemical that is added to products to make them smell or taste extremely bitter and is required in some states, such as California, Oregon, New Mexico, Colorado, and Vermont. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.