WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Chevrolet Suburban

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

978 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIT5391E2019-03-11. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
PIP5554A2019-03-11. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary information communicates P0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
PIT5307F2019-03-11. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
N1821908202019-03-11. Service bulletin. STEERING. N182190820 - Customer Satisfaction Program. Certain vehicles, may have a condition where the power steering belt may slip due to tooth wear-out or poor belt tooth-to-gear tooth fit. Power steering assist may be reduced or lost intermittently, if early warning signs are ignored. Early warnings may include a ?Steering Assist is Reduced? message, audible clicking / squealing sounds, or a change in steering effort. Dealers will replace the steering gear assembly.
PIT5350B2018-12-17. Service bulletin. ENGINE. This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
PIP5570A2018-12-17. Service bulletin. STEERING; ENGINE. This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
PIT5284D2018-12-17. Service bulletin. SEATS. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used to adjust the striker just enough to center in the latch opening. Technician may find a seat bottom latch may have an unequal latch opening side-to-side for the striker to seat into. To repair this condition, with the affected seat in the tumbled forward position, while applying steady, firm pressure, cycle the seat down into the latched position. Some vehicles built prior to 09/21/2015 with 60/40 Split Bench Seat may have 60-percent long side bench, inboard latch may not be properly aligned in striker opening. Technician will need to place a 2.6 mm thick flat washer over the 40 percent seat base stud, not the floor stud. Some vehicles may have a seat base plat that rattles against the rib in the floor pan. Apply Mylar tape to the floor pan under the seat plate to provide relief for the rattle condition.
PIP5477J2018-12-17. Service bulletin. POWER TRAIN. This Preliminary information communicates to the dealer technician that the 10L90 and 10L80 transmissions have been place on a part restriction. Dealers are to contact the Product Quality Center before replacing the transmission assembly.
PIT5445C2018-12-17. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician of additional information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
PIT5594A2018-12-17. Service bulletin. ELECTRICAL SYSTEM. This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.
PIP5606B2018-12-17. Service bulletin. ENGINE. This Preliminary information communicates A vehicle may have a tick noise from the engine cold, initial start in the morning. A lifter may not have sufficient amount of oil during cold start operation (not pumped up). As information comes in the Pi will be updated and when the final repair is out this this PI will be changed to a Bulletin
PIT3946C2018-12-17. Service bulletin. STRUCTURE; EQUIPMENT. This Preliminary Information communicates an issues with the headliner sagging and how to reattach the velcro using Hardman Double Bubble Epoxy part number 04001.
PIT5272B2018-12-17. Service bulletin. STRUCTURE; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a whistle noise in the vehicle from the driver or passenger side. Technician will need to inspect for voids in the body sealer on the left or right side A-pillar. Technician should also inspect for voids in the body sealer at the cowl seam and apply sealer as necessary.
183062018-12-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SEATS. 18306 - Customer Satisfaction Program. Certain 2019 model year Chevrolet Suburban and Tahoe vehicles were built with cloth seats instead of vinyl seats. Dealers will replace the entire front row seat unit.
PIC6086E2018-11-26. Service bulletin. VISIBILITY; VISIBILITY:WINDSHIELD. This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
PIT5550B2018-11-26. Service bulletin. SEATS:MID/REAR ASSEMBLY; SEATS. This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up. This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor. It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well as advising the dealer to look for bent/damaged seat recline mechanisms.
PIT5438E2018-11-26. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
PIP5159C2018-11-26. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on and Diagnostic Trouble Code P0300 - P0308 may set. Technician will inspect for lose sparkplug wire. If a spark plug wire is found lose check for a missing ?C? clip on the wire end for the ignition coil. If the clip is missing replace the wire.
PIP5491A2018-11-13. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.
PIP5570A2018-11-13. Service bulletin. STEERING:GEAR BOX:SHAFT PITMAN; STEERING:GEAR BOX:SHAFT SECTOR. This Preliminary information communicates to the dealer a conditionwhere a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
PIT4322J2018-10-15. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC). This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
PIT5403E2018-10-15. Service bulletin. SUSPENSION. This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
PIT5576B2018-10-15. Service bulletin. STRUCTURE. This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
PIT5361D2018-10-15. Service bulletin. SERVICE BRAKES. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line between the booster and the pump.
PIT5448D2018-10-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.