WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Suburban

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2542 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Software are shown. Show all

Bulletins, newest first
PI0799A2017-12-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
17-NA-2442017-12-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
17-NA-2422017-12-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.
GCUS-9-2862017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. 15304 - Service Update. This bulletin provides a service procedure to reprogram the transfer case control module on the vehicles listed above. In low ambient temperatures, below 5°F (-15°C) a transfer case brake motor assembly malfunction may occur. Diagnostic Trouble Code (C0398 - Range Position Correlation Fault) will be set, locking the transfer case in ?4HI? until the vehicle is serviced. This software update also addresses other transfer case control issues for overall improved drivability.
PIP5411E2017-11-14. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition. Dealer directed to follow latest version of PIP5507 if the fuel pump does not correct the concern.
PIC5492F2017-11-14. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5236H2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
PIT5383C2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles with various Heater-Vent-Air Conditioning blower mode or temperature issues. Technician will need to reprogram the Heater-Vent-Air Conditioning control module using Tis2Web and Service Programming System.
PIC6033A2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have "Service Theft System" message on the Driver Information Center. Technician may find Diagnostic Trouble Code B291B sym 3B and is unable to clear the Diagnostic Trouble Code. Technician will need to restore communication between the Body Control Module and Theft Deterrent Sensor Module to clear the Diagnostic Trouble Code.
07-08-49-020K2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
PIC5588D2017-10-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT5509C2017-10-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
03-08-46-004S2017-08-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIT53502017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
PIC6108A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician to download the USB software from TIS2WEB using the vehicle identification number every time a programming event of the human machine interface module is needed. Damage could be caused to the module if USB programmed with the incorrect software.
PIP4786B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
PIT5365C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
PIT5076E2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIT54052017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician for a reduced power message, steering assist, engine stall or the instrument panel, radio, and or Heater-Vent-Air Conditioning go blank with multiple diagnostic trouble codes. If any of the following diagnostic trouble codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, and U0452 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut.
PIT5383A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have various Heater-Vent-Air Conditioning issues. Technician should use Tis2Web to reprogram the Heater-Vent-Air Conditioning control module.
PIT5362A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles with visible water leak or signs of water intrusion from the antenna base, red OnStar LED, unable to connect to OnStar, OnStar unable to locate the vehicle, OnStar has inaccurate global positioning system location, no global positioning system on the navigation radio display, and inaccurate global positioning system location on the navigation radio display. Technician may find Diagnostic Trouble Codes B2462-02, B2462-04, B2470-02, B2470-04, B125C-01, B125C-02, or B125C-04. Technician should replace the high efficiency antenna with the latest part number in the catalog.
PIP5250B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have Service 4WD message in the Driver Information Center. During inspection technician may find Diagnostic Trouble Code C0398 or C0326 stored in the Transfer Case Control Module. If the vehicle has Regular Production Option Code NP0 and only has diagnostic trouble code C0398 stored in the Transfer Case Control Module, then use Service Programming System to update the Transfer Case Control Module. When working with vehicles equipped NHQ and NQ6 and setting Diagnostic Trouble Code C0398 when operated in areas where the ambient temperature is below 32 Fahrenheit (0 Celsius) use Global Diagnostic System 2 to review the freeze frame failure records, record all findings and Diagnostic Trouble Codes then clear the DTCs and data. Technician will need to operate the vehicle in all ranges and ensure that no Diagnostic Trouble Codes reset. If the vehicle had a Diagnostic Trouble Code C0398 in the Transfer Case Control Module stored with any other Diagnostic Trouble Code such as C0392, C0396, C0306 or other codes related to rotational position sensor or actuator position sensor it is likely that is causing a C0398 to set and replacement of the actuator will likely not repair the vehicle. If no Diagnostic Trouble Codes reset and C0398 was set without other rotational position sensor, or actuator position sensor Diagnostic Trouble Codes then replace the actuator motor with part number 23355888. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIP5250A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center. Technician may find C0398 or C0326 stored in the Transfer Case Control Module. Technician should reprogram the Transfer Case Control Module using Service Programming System for the updated calibrations to resolve this concern.
PIT5365A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
PIT53672017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that may have a blank displays, flashing displays, "Error or Update failed Messages", navigation map not loading, Bluetooth or USB concerns. Technician should inspect the USB/SD card port for a SD card or a device plug into any of the USB ports.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.