Service bulletins for the 2012 Chevrolet Suburban
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1700 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Transmission and driveline are shown. Show all
| PIP4653E | 2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module. |
|---|---|
| 09-07-30-018C | 2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions |
| 16-NA-338 | 2017-08-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns. |
| PIT5442 | 2017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center. |
| PI1343 | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This preliminary bulletin provides a procedure to reprogram the tcm to correct the customers concern of a harsh, tie up feeling from a 6-4 downshift. |
| PI1344A | 2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY. This preliminary bulletin provides a procedure to remove and inspect the clutch select solenoid valve for damage, located in the valve body to correct the customers concern of reduced acceleration at low speeds and trans slip at lauch. |
| PI1343A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This preliminary bulletin provides a procedure to reprogram the tcm to correct the customers concern of a harsh, tie up feeling from a 6-4 downshift. |
| PI0876 | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken. |
| PI0020D | 2017-08-15. Service bulletin. POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT. This preliminary informational bulletin provides technicians with information on the normal condition of white, milky or cloudy appearance of front differential fluid. |
| 06-00-89-026L | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| PIP3119N | 2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIP4112M | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIP4112L | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIT5206 | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ELECTRICAL SYSTEM; SERVICE BRAKES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. |
| PIP5102 | 2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT. This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P0016 stored. Technician will need to inspect the reluctor on the crankshaft. If the reluctor has moved replace the crankshaft. |
| PIP5087 | 2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician about vehicles that may have a service 4WD message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0379. Technician will need to inspect the front axle actuator connector for signs of moisture intrusion. If there is corrosion on the terminals at either location replace the actuator and harness. |
| PIP4828A | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a rough idle and/or momentary lack of power after cold starting the engine and immediately placing the transmission in gear. Technician should follow published Service Information diagnostics first. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIP4138L | 2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter. |
| PIT4505F | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that have a rattle, buzz, tick, or vibration type noise that appears to be coming from the center of the dash. Technician will adjust the transmission dipstick tube away from the front of cowl to provide additional clearance. |
| PIP3720D | 2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design. |
| PIP4681D | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician about vehicles that have a random bump, chuggle, or fishbite sensation when crowding the throttle slightly with the Torque Converter Clutch on while cruising at 35-60 miles per hour. Technician should follow all published Service Information diagnostics if the concern is repaired compare to a like vehicle with the same options. |
| PIP4765A | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. If Service Information diagnosis isolates no compression on the misfiring cylinder(s) with 100% leakage into the crankcase, perform the following steps as necessary before disassembling the engine. Technician will use a lighted bore scope if available to inspect the top of the related piston(s) through the spark plug hole to determine if any of the pistons are melted. If damaged piston(s) are found inspect for aftermarket parts. Also use the latest version of 09-06-04-026 to verify if there are aftermarket calibrations in the Engine Control Module. Take photos and document accordingly if anything is found. |
| PIT5206A | 2017-08-15. Service bulletin. SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages " Brake Pedal Override Feature ", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. |
| PI1343B | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This preliminary informational bulletin provides a procedure to reset the transmission adapts and test drive in additon to a transmission control module reprogram to correct a harsh or tie up feeling from 6-4 downshift |
| PIT5206C | 2017-08-15. Service bulletin. SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.