WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2175 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIP55412018-02-21. Service bulletin. POWER TRAIN; ENGINE; SUSPENSION. This Preliminary information communicates to the dealer technician using the PICO scope will aid in determining if the if the engine or transmission is root cause of a vibration or shudder concern.
PIP5537A2018-01-16. Service bulletin. POWER TRAIN. This Preliminary information communicates to the dealer technician how to diagnose for a possible damaged or broken pushrod.
PIP55372018-01-16. Service bulletin. POWER TRAIN. This Preliminary information communicates to the dealer technician how to diagnose for a possible damaged or broken pushrod.
PIP5245B2018-01-16. Service bulletin. POWER TRAIN. This Preliminary Information communication provides information to the technician on how to diagnose vehicles with various noises associated with four wheel drive operation. Before beginning any diagnosis it is imperative to review the Symptoms - Transfer Case in Service Information and perform the necessary inspections. In all cases the complaint vehicle should be compared to another like vehicle before beginning any repairs.
GCUS-3-8892017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 17108 - Service Update. Certain vehicles may have a fracture in the parking lever support window which, if overloaded, may result in a further fracture of the transmission case. This may cause the park system to be inoperative. Dealers will inspect transmission case for mold number and Julian date and replace suspect transmission.
GCUS-3-8862017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 17098 - Service Update. Certain vehicles may have a condition where a false failure action is being taken when it is not required. This condition can result in the transmission holding the last known safe gear for 6 seconds. A malfunction indicator lamp (MIL) is set when this default happens more than 2 times, and reduced propulsion can happen for all 8-speed transmission applications. Dealers will reprogram the transmission control module (TCM).
PIT5202D2017-12-14. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
PIP55312017-12-14. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
GCUS-3-9022017-10-15. Service bulletin. POWER TRAIN. 17108 01 - Service Update (revised parts list). Certain vehicles may have a fracture in the parking lever support window which, if overloaded, may result in a further fracture of the transmission case. This may cause the park system to be inoperative. Dealers will inspect transmission case for mold number and Julian date and replace suspect transmission.
PIP55042017-10-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information and definitionsto the technician about vehicles that have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed and no debris is found in the transmission fluid pan the technicians are instructed to flush the transmission fluid three times. If debris is found in the transmission fluid pan the technicians are instructed to also replace the torque converter.
16-NA-3382017-08-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
16-NA-1752017-08-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 48 and 104 KM/H (30 and 65 MPH) at a steady state.
PIP54462017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
PIP5437A2017-08-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have harsh concerns. Technician are advised to use GDS2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
PIP5382H2017-08-15. Service bulletin. WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner’s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
16-NA-4042017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This technical bulletin provides a procedure to reprogram the TCM to correct the DTC set.
16-NA-1752017-08-15. Service bulletin. POWER TRAIN. This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
PIP54742017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT. This Preliminary information communicates that a technician might find a vehicle with no power transmitted to the front axle in four wheel drive. If vehicle has regular production option NQF the technician finds that with vehicle in four wheel drive with solid indicator light but the front wheels do not assist in moving vehicle he is to verify when shifting the transfer case to four wheel drive the light is solid If that switch illuminated solid then all operations to achieve four wheel drive were completed successfully. Technician is to inspect pictured item and ensure that the body ring that the synchronizer engages has not separated from theTransfer Case Front Output Shaft Drive Sprocket. If so then replace the transfer case front output drive shaft sprocket as needed. If vehicle has regular production option NQG and the customer indicates that the transfer case was in four wheel drive with that indicator light on solid in the instrument panel cluster but the front wheels were not assisting in vehicle movement technician is to verify the following, shift the transfer case to four wheel drive and ensure that the four wheel drive in the instrument panel cluster is on solid. Technician is to inspect pictured item and ensure that the body ring that the synchronizer engages has not separated from theTransfer Case Front Output Shaft Drive Sprocket.If so then replace the transfer case front output drive shaft sprocket as needed.
PIP5457B2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that have a hesitation, chuggle, fishbite or roughness that can be felt in 3rd to 6th gear, torque converter clutch on, low rpm, when tipping into throttle to load engine. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5457A2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that have a hesitation, chuggle, fishbite or roughness that can be felt in 3rd to 6th gear, torque converter clutch on, low rpm, when tipping into throttle to load engine. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP3119N2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
PIP54572017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician about vehicles that have a hesitation, chuggle, fishbite or roughness that can be felt in 3rd to 6th gear, torque converter clutch on, low rpm, when tipping into throttle to load engine. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
16-NA-4042017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This technical bulletin provides a procedure to reprogram the TCM to correct the DTC set.
16-NA-3642017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY. This technical bulletin provides a procedure on how to test and perform a clutch learn procedure to correct delayed clutch engagement.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.