Service bulletins for the 2015 Chevrolet Silverado
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
3099 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIP5337B | 2017-03-21. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE A SHAKE OR SHUDDER DURING LIGHT THROTTLE ACCELERATION, BETWEEN 30 AND 65 MPH STEADY STATE DRIVING. ALSO SHUDDER FEELING THAT MAY BE DESCRIBED AS DRIVING OVER RUMBLE STRIPS OR ROUGH PAVEMENT. TECHNICIAN WILL DRIVE THE VEHICLE AND MONITOR THE TORQUE CONVERTER CLUTCH SLIP. THE TORQUE CONVERTER CLUTCH SLIP SPEED SHOULD BE 10 RPM OR LESS ALSO NOTE IF THE SHUDDER TAKES PLACE DURING TORQUE CONVERTER CLUTCH APPLY. IF THE TORQUE CONVERTER CLUTCH SLIP SPEED IS IN THE RANGE OF 10 RPM OR LESS THE CONDITION IS POSSIBLY RELATED TO ENGINE PERFORMANCE. IF THE SHUDDER IS ONLY PRESENT IN 4 CYLINDER MODE AND TORQUE CONVERTER CLUTCH SLIP IS 10 RPM OR LESS DEEM THE SHUDDER CONCERN NORMAL CHARACTERISTIC OF ACTIVE FUEL MANAGEMENT. IF THE SLIP SPEED IS BEYOND 10 RPM OR THERE IS SHUDDER DURING TORQUE CONVERTER CLUTCH APPLY THE TORQUE CONVERTER WILL NEED TO BE REPLACED. |
|---|---|
| PIP5261A | 2017-03-21. Service bulletin. POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A HIGH PITCHED WHINE NOISE FROM THE VEHICLE NOTICED WHEN DRIVING IN AUTO 4WD. WHEN THE TRANSFER CASE CONTROL MODULE HAS TO MOVE THE TRANSFER CASE ACTUATOR MOTOR THE HIGHER CURRENT PASSING THROUGH THE MODULE CAUSES AN "ELECTRONIC BUZZ OR WHINE" WITHIN SOME OF THE CAPACITORS IN THE MODULE THAT CAN BE HEARD BY SOME OF OUR CUSTOMERS. THIS CAN ONLY BE HEARD WITH ALL ACCESSORIES AND HVAC OFF AND ONLY WHEN ACTUATOR MOVEMENT IS REQUIRED. THIS DOES NOT INDICATE A CONCERN WITH THE MODULE AND SHOULD NOT BE REPLACED TO ADDRESS THIS CONCERN. |
| PIP5248B | 2017-03-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:MANUAL TRANSMISSION. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS NEED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE STALLING SHUDDER AND/OR HARD SHIFTING INTO 1ST GEAR OR REVERSE VIBRATION ON LAUNCH (WITH EXCESSIVE CRANKSHAFT END PLAY). TECHNICIAN WILL TEST TO DETERMINE IF THE CRANK SHAFT END PLAY IS WITHIN SPECIFICATION 0.0015–0.0086 INCH. IF END PLAY IS FOUND TO BE OUT OF SPECIFICATION, REMOVE ENGINE AND INSPECT FOR POSSIBLE CRANKSHAFT THRUST BEARING AND/OR CRANKSHAFT FOR WEAR. INSPECT THRUST BEARING FOR WEAR ON ONE SIDE AND CRANKSHAFT ON THAT “MATING” SURFACE. IF THE THRUST BEARING HAS THREE VERTICAL CHANNELS WORN OFF REPLACE CONNECTING ROD BEARINGS, MAIN BEARINGS, THRUST BEARING AND CRANKSHAFT. IF WORKING ON A CORVETTE THE OIL TANK WITH LINES AND OIL COOLER ARE BOTH REQUIRED TO BE REPLACED IF EQUIPPED. |
| PIP5245A | 2017-03-21. Service bulletin. EQUIPMENT; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE VEHICLES WITH VARIOUS NOISES ASSOCIATED WITH FOUR WHEEL DRIVE OPERATION. BEFORE BEGINNING ANY DIAGNOSIS IT IS IMPERATIVE TO REVIEW THE SYMPTOMS - TRANSFER CASE IN SERVICE INFORMATION AND PERFORM THE NECESSARY INSPECTIONS. IN ALL CASES THE COMPLAINT VEHICLE SHOULD BE COMPARED TO ANOTHER LIKE VEHICLE BEFORE BEGINNING ANY REPAIRS. |
| PIP5230C | 2017-03-21. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN BEFORE REPLACING THE CRANKSHAFT TO REVIEW THE FOLLOWING. DEALER SHOULD COMPLETE THE SERVICE INFORMATION DIAGNOSTICS AND THE COST COMPARISON WORKSHEET FOR ASSEMBLY REPAIR VS REPLACEMENT. TECHNICIAN WILL USE THE LATEST VERSION OF 09-06-04-026G TO VERIFY THE ECM CALIBRATION IS NOT AN AFTERMARKET CALIBRATION. IF THE CUSTOMER PREFERS TO KEEP THE ORIGINAL NUMBERS MATCHING ENGINE PLEASE CALL TAC FOR REPAIR DIRECTION. |
| PIP5224C | 2017-03-21. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN:AUTOMATIC TRANSMISSION. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE ALLISON LCT1000 VALVE BODY PART NUMBER 24262535 HAS BEEN PLACED ON RESTRICTION THROUGH GENERAL MOTORS PRODUCT QUALITY CENTER. DEALER WILL NEED TO CALL GENERAL MOTORS PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE. |
| PIP5189A | 2017-03-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT MAY HAVE BLACK SMOKE ON A COLD START. A DUAL-PULSE INJECTION STRATEGY IS UTILIZED DURING ENGINE COLD START TO REDUCE THE TIME REQUIRED TO BRING THE CATALYTIC CONVERTER UP TO OPERATING TEMPERATURE. THIS SPLIT INJECTION STRATEGY LASTS FOR ABOUT 60 SECONDS ON COLD START. THIS PROCESS MAY CAUSE THE CUSTOMER TO SEE INCREASED BLACK SMOKE DURING COLD START AND SHOULD BE CONSIDERED NORMAL. |
| PIP5104B | 2017-03-20. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A COLD ENGINE TICK NOISE FOR 50 SECONDS AT START UP. TECHNICIAN DETERMINES IF THE TICK NOISE IS POSSIBLY COMING FROM THE EXHAUST MANIFOLD, AS THIS NOISE COULD EASILY BE MISTAKEN FOR AN ENGINE TICK NOISE. IF YOUR SI DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN, THIS CONCERN SHOULD BE CONSIDERED A VEHICLE DESIGN CHARACTERISTIC OF THE ECM CALIBRATION AND NO ADDITIONAL REPAIRS SHOULD BE PERFORMED. |
| PIP4912D | 2017-03-20. Service bulletin. EQUIPMENT; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON VEHICLES THAT MAY HAVE AN INTERMITTENT HIGH IDLE. IF A TECHNICIAN HAS DUPLICATED, OR THE CUSTOMER DESCRIPTION ALIGNS WITH THE SPEEDS MENTIONED IN THE IDLE SPEED DESCRIPTION TABLES, THE IDLE SPEED SHOULD BE CONSIDERED A NORMAL CHARACTERISTIC OF CURRENT VEHICLE DESIGN. |
| PIC6170 | 2017-03-17. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS NEED TO DIAGNOSE AND REPAIR VEHICLE THAT MAY HAVE A CONCERN WITH NAVIGATION ICON NOT SHOWING THE CORRECT LOCATION THEN JUMPING TO THE CORRECT LOCATION. THE POSITION INDICATOR MAY SHOW THE VEHICLE TURNING IN THE OPPOSITE DIRECTION OR MAY SHOW THE VEHICLE TRAVELING OFF THE ROAD. TECHNICIAN WILL INSPECT THE HUMAN MACHINE INTERFACE MOUNTING. FOLLOW SERVICE INFORMATION FOR THE CORRECT ORIENTATION OF THE HUMAN MACHINE INTERFACE. |
| 14-08-79-001 | 2017-03-16. Service bulletin. EQUIPMENT. THIS INFORMATIONAL BULLETIN PROVIDES A LIST OF PARTS/REPLACEMENT PARTS FOR THE TONNEAU COVERS. |
| PIT5367 | 2017-03-16. Service bulletin. ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A BLANK DISPLAYS, FLASHING DISPLAYS, “ERROR OR UPDATE FAILED MESSAGES”, NAVIGATION MAP NOT LOADING, BLUETOOTH OR USB CONCERNS. TECHNICIAN SHOULD INSPECT THE USB/SD CARD PORT FOR A SD CARD OR A DEVICE PLUG INTO ANY OF THE USB PORTS. |
| PIT5365A | 2017-03-16. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW THE RADIO DISPLAY GETS THE AIR AMBIENT TEMPERATURE. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO4, IO5, OR IO6 THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO4, IO5, OR IO6 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. |
| PIT5365 | 2017-03-16. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW THE RADIO DISPLAY GETS THE AIR AMBIENT TEMPERATURE. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO4, IO5, OR IO6 THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO4, IO5, OR IO6 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. |
| PIT5312A | 2017-03-16. Service bulletin. STEERING:COLUMN. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE A GRIND, POP, SHUDDER OR BIND FEELING/NOISE IN THE STEERING COLUMN WHEN TURNING LEFT OR RIGHT. TECHNICIAN WILL INSPECT FOR THE LOWER COLUMN BEARING TO BE OUT OF POSITION AND THE UPPER INTERMEDIATE STEERING SHAFT TO LOWER COLUMN SHAFT BOLT AND NUT MAY BE CONTACTING THE INHIBITOR/SHIFTIER CABLE BRACKET. TECHNICIAN WILL REPLACE THE STEERING COLUMN FOR THIS CONCERN. |
| PIT4539S | 2017-03-16. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE DRIVE MOTOR GENERATOR CONTROL MODULE AND ACCESSORY POWER MODULE ARE BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE. |
| PIT3271G | 2017-03-16. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT CHANGING THE TIRE AND WHEEL SIZE ON VEHICLES. GENERAL MOTORS WILL ONLY SUPPORT A TIRE CALIBRATION FOR TIRES THAT HAVE BEEN SIZED, TESTED AND DESIGNED FOR THE VEHICLE IN QUESTION AND ITS APPLICATIONS. TECHNICIAN SHOULD NOT USE THE INFORMATION THAT IS PROVIDED BY THE ANTILOCK BRAKING SYSTEM TIRE SIZE SELECTION. |
| PIP5261 | 2017-03-16. Service bulletin. POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A HIGH PITCHED WHINE NOISE FROM THE VEHICLE NOTICED WHEN DRIVING IN AUTO 4WD. WHEN THE TRANSFER CASE CONTROL MODULE HAS TO MOVE THE TRANSFER CASE ACTUATOR MOTOR THE HIGHER CURRENT PASSING THROUGH THE MODULE CAUSES AN "ELECTRONIC BUZZ OR WHINE" WITHIN SOME OF THE CAPACITORS IN THE MODULE THAT CAN BE HEARD BY SOME OF OUR CUSTOMERS. THIS CAN ONLY BE HEARD WITH ALL ACCESSORIES AND HVAC OFF AND ONLY WHEN ACTUATOR MOVEMENT IS REQUIRED. THIS DOES NOT INDICATE A CONCERN WITH THE MODULE AND SHOULD NOT BE REPLACED TO ADDRESS THIS CONCERN. |
| PIP5259 | 2017-03-16. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON WITH DIAGNOSTIC TROUBLE CODE P0300 AND AN ENGINE MISFIRE. TECHNICIAN WILL NEED TO INSPECT THE VALVE OPERATION, IF THE VALVE OR VALVES ARE NOT MOVING THE ACTIVE FUEL MANAGEMENT LIFTERS AND GUIDE ON THE BANK WITH THE CONCERN AND THE OIL PUMP AND OIL PAN ASSEMBLY SHOULD BE REPLACED. |
| PIP5230A | 2017-03-15. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN BEFORE REPLACING THE CRANKSHAFT TO REVIEW THE FOLLOWING. DEALER SHOULD COMPLETE THE SERVICE INFORMATION DIAGNOSTICS AND THE COST COMPARISON WORKSHEET FOR ASSEMBLY REPAIR VS REPLACEMENT. TECHNICIAN WILL USE THE LATEST VERSION OF 09-06-04-026G TO VERIFY THE ECM CALIBRATION IS NOT AN AFTERMARKET CALIBRATION. IF THE CUSTOMER PREFERS TO KEEP THE ORIGINAL NUMBERS MATCHING ENGINE PLEASE CALL TAC FOR REPAIR DIRECTION. |
| PIP5223B | 2017-03-15. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE E92 ECM RESTRICTION PART NUMBER 12662034 WILL BE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS PRODUCT QUALITY CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE. |
| PIP5213A | 2017-03-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE LCT1000 6 SPEED ALLISON AUTOMATIC TRANSMISSION IS ON RESTRICTION THROUGH GENERAL MOTORS PRODUCT QUALITY CENTER. DEALER WILL NEED TO CALL GENERAL MOTORS PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE. |
| PIP5204E | 2017-03-15. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE DIESEL OXIDATION CONVERTER PART RESTRICTION HAS ENDED. DEALER CAN NOW ORDER THE PARTS THROUGH THE REGULAR CUSTOMER CARE AND AFTERSALES PARTS PROCESS. |
| PIP4568R | 2017-03-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. TECHNICIAN WILL FOLLOW SERVICE INFORMATION DIAGNOSIS FIRST. IF SERVICE INFORMATION DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN PERFORM A CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT SYSTEM COMPRESSION TEST IN SERVICE INFORMATION. IF THE RUNNING COMPRESSION OF THE MISFIRING CYLINDER STAYS BELOW 25 POUNDS PER SQUARE INCH REGARDLESS OF THE ACTIVE FUEL MANAGEMENT SOLENOID BEING COMMANDED ON OR OFF, AN ACTIVE FUEL MANAGEMENT LIFTER IS MECHANICALLY COLLAPSED/STUCK OR UNLOCKING AS SOON AS THE ENGINE IS STARTED. REPLACE ALL ACTIVE FUEL MANAGEMENT LIFTERS, AND ALL PLASTIC LIFTER GUIDES. ALSO PERFORM THE CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT VALVE LIFTER OIL MANIFOLD DIAGNOSIS AND TESTING IN SERVICE INFORMATION. IF IT ISOLATES A CONCERN WITH THE VALVE LIFTER OIL MANIFOLD, REPLACE IT AND REEVALUATE THE CONCERN. THE ACTIVE FUEL MANAGEMENT LIFTERS CAN ALSO BE MONITORED FOR PROPER OPERATION BY CAREFULLY INSPECTING THE CYLINDER 1, 4, 6, AND 7 ROCKERS AND VALVES WHILE CRANKING OR BRIEFLY AND SAFELY RUNNING THE ENGINE WITH THE VALVE COVERS REMOVED. IF THE VALVE OR VALVES OF AN ACTIVE FUEL MANAGEMENT CYLINDER STOP MOVING WHILE DOING THIS TEST, THE ACTIVE FUEL MANAGEMENT LIFTER IS CAUSING THE CONCERN. FOR 2008-2009 FULL SIZE TRUCK/SUV OR A 2007-2009 CHEVROLET TAHOE WITH THE POLICE PACKAGE REPROGRAM THE ENGINE CONTROL MODULE. ON THE 2008-2009 PONTIAC G8, 2010-2011 CAMARO, AND 2007-2010 FULL SIZE TRUCKS WITH ACTIVE FUEL MANAGEMENT, ALSO DETERMINE IF THE ACTIVE FUEL MANAGEMENT PRESSURE RELIEF VALVE SHIELD THAT IS LISTED IN THE LATEST VERSION OF 10-06-01-008 HAS EVER BEEN INSTALLED. ON PASSENGER CARS WITH THE LS4 ENGINE, DETERMINE IF THE UPDATED OIL PAN GASKET THAT IS LISTED IN THE LATEST VERSION OF 11-06-01-007 HAS BEEN INSTALLED. |
| PIC3278F | 2017-03-14. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.