WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

3099 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
PIP5437A2017-08-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have harsh concerns. Technician are advised to use GDS2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
PIT5389B2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT5311A2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector from General Motors Customer Care and Aftersales along with the trailer's 7-way connector plug.
PIT5282A2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the X185 or the X138 connector (varies with vehicle build; refer to Service Information) near the underhood fuse block, terminal 32. Circuit 47 ends at the body harness side of X185 or X138 terminal 32, which comes from the X61A junction block. Obtain enough Dark Blue 12 gauge wire to run from X185 or X138 to the 7-way trailer connector at the bumper. Attach terminated lead part number 13327155 to one end of the Dark Blue and insert into the chassis harness side of the X185 or X138 connector terminal 32. Run the Dark Blue wire in its own conduit along the frame to the 7-way trailer connector at the bumper. Remove circuit 47 from the 7-way trailer connector terminal ?C? and tape the bare terminal and attach to the harness. Attach terminal part number 12110853, located in Delphi Tray 4, to the other end of the Dark Blue wire, with the correct weather pack seal, and insert it into the 7-way trailer connector terminal ?C.? Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
PIP52502017-08-15. Service bulletin. POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center. Technician may find C0398 or C0326 stored in the Transfer Case Control Module. Technician should reprogram the Transfer Case Control Module using Service Programming System for the updated calibrations to resolve this concern.
PIP5211B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track
PIT53592017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a radio backlighting will stay on even after the ignition has been turned off and the key has been removed for several minutes, eventually the battery will drain. Technician may find following fuses F23DL F22DL F30DL F31DL F32DL with the ignition key in the off position to have voltage. Technician should not replace the Transfer Case Control Module. Technician will need to install a diode, part number 12112422, across the coil of the solenoid. It is important that the striped end of the diode be connected to the positive terminal of the coil and the other end of the diode be connected to ground.
PIT5288B2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
PIT5074H2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIC60532017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that the radio will lose audio except warning chimes and become inoperative after using Siri. The concern may be corrected by an ignition cycle. If the radio continues to be inoperative please contact General Motors Technical Assistance for further direction.
PIT5287A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
PIT5236A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
PIT5436A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles with wireless fidelity inoperative after the OnStar module was replaced. Technician will need to perform a WIFI Activation using Service Programming System.
PIT53542017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
PIC5492C2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT53502017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
PIT53432017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Preliminary Information communication provides information to the technician about when starting the vehicle there is a lack of air flow through the Heater-Vent-Air Conditioning vents and that the indicators on the Heater-Vent-Air Conditioning controls are illuminated and the display may show Heater-Vent-Air Conditioning off. Technician should reprogram the Heater-Vent-Air Conditioning control module using Service Programming System with the latest calibration.
PIT54362017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles with OnStar WIFI is inoperative after a VCIM replacement. Technician will need to contact General Motors Technical Assistance Center with module information.
PIC61182017-08-15. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:FRAME AND MEMBERS. This Preliminary Information communication provides information to the technician about vehicles that have a loss of audio after wiping/cleaning the dash. Technician will update the radio using Service Programming System to repair the concern.
PIT5236F2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
PIT5236E2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
PIC5932A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIT54492017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. This Preliminary Information communication provides information to the technician for a service trailer brake message on in the vehicle. The technician will find diagnostic trouble codes C1115, C1116, C1117, or C1118. In most cases the chassis control module is not the cause of the trouble codes. The technician should inspect the wiring between the chassis control module and the trailer brake control switch. The inline connectors X185 or X138 as well as the connectors X1 and X5 of the X61A junction block should be thoroughly inspected looking for backed out, loose, poor retention or any other terminal issues. If there are no wiring concerns are found the trailer brake control switch is most likely the cause.
PIT54452017-08-15. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician of addition information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
PIT54382017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.