WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2332 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Brakes are shown. Show all

Bulletins, newest first
PIT4826B2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS; SERVICE BRAKES; SERVICE BRAKES, AIR:DISC:PADS. This Preliminary Information communication provides information to the technician about hairline cracks may be noticed in the pad friction material, when performing a brake inspection. Technician should be advised that the hairline cracks do not affect the operation of the brake system and the pads should not be replaced if only hairline cracks are found.
PIT4169F2017-08-15. Service bulletin. SERVICE BRAKES, ELECTRIC; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have a "Service Stability Message" appears on the Drivers Information Center. Technician will find Diagnostic Trouble Code C0561 set in the Electronic Brake Control Module. Technician will need to address any other Diagnostic Trouble Codes that are set in the vehicle first before working on Diagnostic Trouble Code C0561.
PIT5206A2017-08-15. Service bulletin. SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages " Brake Pedal Override Feature ", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor.
PIT5202B2017-08-15. Service bulletin. SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
PIT5206C2017-08-15. Service bulletin. SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.
PIT5206B2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages "Brake Pedal Override Feature", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor.
PIP5092A2017-08-15. Service bulletin. PARKING BRAKE:DRIVELINE. This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
PIP51752017-08-15. Service bulletin. PARKING BRAKE; ENGINE AND ENGINE COOLING; WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
PIT4943C2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIT5206E2017-05-22. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; PARKING BRAKE; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES “ BRAKE PEDAL OVERRIDE FEATURE “, TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205.
PIT4383Q2017-05-22. Service bulletin. SERVICE BRAKES, AIR:SUPPLY:CHECK VALVE; SERVICE BRAKES, AIR:SUPPLY:LOW PRESSURE WARNING:SWITCH. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE ELECTRONIC BRAKE CONTROL MODULE AND BRAKE PRESSURE MODULATOR VALVE FOR THE 2-MODE HYBRID UTILITIES AND TRUCKS ARE NOW OFF RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER.
PIT-3665-D2016-08-24. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HYDRO-BOOST IS NOT SERVICEABLE AND WILL NEED TO BE REPLACED IF THE BRAKE PEDAL MOVES OR APPLIES ON ITS OWN AT A FULL TURN.
PIT-4383-P2016-08-24. Service bulletin. EQUIPMENT; SERVICE BRAKES, ELECTRIC. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE ELECTRONIC BRAKE CONTROL MODULE AND BRAKE PRESSURE MODULATOR VALVE FOR THE 2-MODE HYBRID UTILITIES AND TRUCKS ARE BEING PLACED ON PARTS ORDERING RESTRICTION THROUGH THE GM TECHNICAL ASSISTANCE CENTER (TAC).
PIT52022016-04-26. Service bulletin. SERVICE BRAKES. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT52062016-04-26. Service bulletin. SERVICE BRAKES. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-10-05-23-001C2016-04-26. Service bulletin. SERVICE BRAKES, AIR:DISC; SERVICE BRAKES, AIR:DRUM. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT-52062013-05-09. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING:ENGINE; SERVICE BRAKES, HYDRAULIC. GENERAL MOTORS: OWNERS MAY COMPLAIN ABOUT UNWANTED BRAKING, OR REDUCED ENGINE POWER. THERE MAY ALSO BE SOME UP AND DOWN SHIFTS WITH THE TRANSMISSION. *KB UPDATED 10/15/14. *PE UPDATED 11/12/14. *PE
PIT-51812012-11-28. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. CHEVROLET/GMC/CADILLAC: BRAKE PEDAL POSITION (BPP) SENSOR HAS RELATED ISSUES AFTER NORMAL DIAGNOSTICS, REGARDING CONNECTOR X205, TERMINAL CONCERN, CRUISE/BRAKE LIGHT OR SERVICE STABILITY MESSAGE OR REDUCED ENGINE POWER. MODELS 2012-2013 ALL ESCALADES, AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA AND ALL YUKONS. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.