Service bulletins for the 2013 Chevrolet Impala
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1539 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIT5353A | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL; EQUIPMENT. This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability. |
|---|---|
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP5216D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP3423M | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft. |
| PIP4919E | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal. |
| PIC5953B | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact. |
| PIP5338 | 2017-08-15. Service bulletin. SUSPENSION; STRUCTURE:FRAME AND MEMBERS. This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number. |
| PIP5095C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP5331 | 2017-08-15. Service bulletin. EQUIPMENT; EQUIPMENT:MECHANICAL; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles with a rattle, tick, or knock type noise. Technician will use chassis ears to listen to the right and left side of the engine and isolate which bank the noise is from. Technician should now remove the piston and rod assemblies from the affected bank to inspect for a loose rod bushing in the rod, or a loose wrist pin in the bushing. There should be no metal through the oil and a piston and rod assembly will repair this noise. If technician finds metal refer to the latest version of PIP5216. If no wrist pins or bushings are found loose and all other diagnostics for this type of noise has been exhausted then engine replacement may be necessary. |
| PIC5666B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about police vehicles that the radar gun inoperative due to Vehicle Speed Sensor signal not provided. Technician will measure the voltage or hertz on circuit 818 if no voltage or signal contact Techline Customer Support Center for further assistance. |
| PIP3423L | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft. |
| PIP5191A | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest. |
| PIT3099N | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIT5389B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system. |
| PIT5236B | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module. |
| PIP5209B | 2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump. |
| PIT5074H | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel. |
| PIP5247 | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Technician must follow published Service Information diagnostics for P06DE. If diagnostics lead to removing the oil pan or engine oil pressure is below specification when hot, to inspect the oil piston nozzles for damage. Technician should replace the broken oil nozzle(s) as long as the engine does not have any damage which warrants engine replacement. |
| PIT5236A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492. |
| PIT5353 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability. |
| PIC5492C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation. |
| PIP5029F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIT5264B | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available. |
| PIT5236F | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.