Service bulletins for the 2008 Chevrolet Express
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1086 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIP5258A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0011. If the technician has followed all published Service Information diagnosis and has not come to a conclusion, technician should check the oil pressure at the oil pressure sender. Then the number two cam bearing should be inspected. |
|---|---|
| PIP5276D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a UPF48R if one is available. |
| PIP5276C | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a PF48 if one is available. If there is no availability of oil filter PF48 use oil filter UPF48R. |
| PIP4932D | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake. |
| PIP5016B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice. |
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIT5058C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about the operation and diagnostics of the Regular Production Option Code UJ1 brake warning pressure warning system. The technician can test the operation of the brake warning system. If the warning system does not function correctly, technician will need to inspect circuit 33 for a short to ground between X141 and the Instrument Panel Cluster terminal 14. Then inspect check circuit 33 for an open between X141 and the Instrument Panel Cluster terminal 14. Also technician should check male side of X141 circuit 33 with an ohm meter to ground and should be close to 0 ohms with engine off and key on. Start engine and circuit should go (OL) indicating that the flow switch opened. Then, turn the steering to the stop in pressure relief and verify that the circuit stays (OL) to check the operation of the pressure switch. |
| PIP4404F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary. |
| PIP3504D | 2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL. This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. If the fuel found in the vehicle has an American Petroleum Institute specific gravity reading of 39 - 44, and the fuel sample you used for comparison has an American Petroleum Institute specific gravity reading of 30 - 39, drain the fuel system and refill with a known good diesel fuel and retest. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5029F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIP5276E | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. Inspect the engine for any oil leaks and repair if need. Technician should change the engine oil and replace the oil filter using a PF48e type filter. |
| PIP5016A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice. |
| PIP5232C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5276F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover. |
| 11-00-90-001A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils. |
| 00-06-01-026G | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| 15-00-90-001 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and filter. |
| 07-06-04-019E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set. |
| 15-00-89-004A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. |
| 00-06-01-026F | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| 02-06-01-027C | 2017-08-15. Service bulletin. ENGINE. This informational bulletin provides technicians with information to help educate them on the many various combinations of engines, interfacing equipment and vehicle usage which may cause higher than expected oil consumption. |
| 06-00-89-026L | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| 06-06-01-010B | 2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE AND ENGINE COOLING. This informational bulletin provides information on close-coupled converter and engine replacement. |
| PIP5029H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.