Service bulletins for the 2012 Chevrolet Equinox
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1847 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| 15-00-90-001 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and filter. |
|---|---|
| 07-06-04-019E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set. |
| 15-00-89-004A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. |
| 00-06-01-026F | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| 13-06-01-003G | 2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE AND ENGINE COOLING. This technical bulletin provides diagnostic and repair information on performing an oil consumption test and/or installing piston and piston ring kit to correct a customer concern for excessive oil consumption. |
| 06-00-89-026L | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| 06-06-01-010B | 2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE AND ENGINE COOLING. This informational bulletin provides information on close-coupled converter and engine replacement. |
| PIP5095D | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP5029H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years. |
| PIP5180A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve. Technician will need to review the latest version of PIP5029 and perform a cold compression test if the concern is only a Hard Start Cold. |
| PIP5062B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations. |
| PIP5029D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIP5029C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIP4964B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution. |
| PIP5095A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP5095 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP5093 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that may have an engine oil leak that appeared as they were driving the vehicle in extremely cold ambient temperatures. The technician may find the oil leak is coming from the rear main seal. Technician will need to check for proper thermostat operation by following thermostat Diagnosis as outlined in Service Information and replace the thermostat as necessary. Also the technician will remove the cam cover, inspect the positive crankcase ventilation baffle inside, and replace the cam cover if obvious sludge build up is present. Any debris in the positive crankcase ventilation pipes, hoses, the positive crankcase ventilation nipple on the cam cover, and the throttle body should be cleaned out. Technician should inspect the related positive crankcase ventilation hoses/connections for potential damage and replace if necessary. Run the engine at operating temperature for 15 minutes at idle. Then turn the engine off, and drain the engine oil for at least 15 minutes to remove all oil and condensation or water from the crankcase. Follow Service Information repair procedures to repair any oil leaks that were induced as a result of the frozen positive crankcase ventilation system and excessive crankcase pressure. Technician should insure the Engine Control Module calibrations have been installed to adjust the engine oil life monitor to a maximum of 7,500 miles (12,070 KM) as well. |
| PIP4384G | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician with a supplement to the Service Information timing procedure for the high feature V-6 engine. Technician will also review the training video on the Common Training Website. |
| PIP4495D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice. |
| PIP5062A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations. |
| PIT3173C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center. |
| PIP5078 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician that service replacement engine part number 12655766 may be received when a service replacement engine is ordered. Technician will need to part off the original engine. |
| PIP4959C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information about vehicles that misfires or roughness on cold start up. Technician may find Diagnostic Trouble Code P0300 set. Technician will need to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. If coolant is found in the cylinder technician will need to contact General Motors Product Quality Center for engine replacement. |
| PIP4959D | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required. |
| PIP5095B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.