Service bulletins for the 2010 Chevrolet Equinox
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1688 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIT3173C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center. |
|---|---|
| PIP5025B | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that may have excessive oil consumption. Technician will need to update the Engine Control Module with the latest calibration in Tis-2-Web. Technician will also perform an oil consumption test by following the latest version of bulletin 01-06-01-011. |
| PIP5028D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P01285 and or P0171. Technician will need to use published Service Information diagnostics first. Technician will update the Engine Control Module with the latest calibration in Tis-2-Web if published Service Information diagnostics do not resolve the concern. If the calibration did not repair the concern inspect the engine for oil leaks and insure the oil fill cap is properly closed. Technician will also use the CH-44175-1 handheld tester to test the ethanol content of the fuel. Technician should also inspect for unmetered air/vacuum leaks by using the Evaporative Emissions System smoke machine to induce smoke into the engine, exhaust, and air intake system as outlined in the latest version of PIP4925. Technician should inspect the air filter condition to ensure that it is a factory filter and that none of the pleats are damaged and the inside of the air cleaner opening before the Mass Air Flow sensor for any sign of casting flash. If the concern is currently happening while at a hot idle, plug all vacuum lines. |
| PIP5025A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that may have excessive oil consumption. Technician will need to update the Engine Control Module with the latest calibration in Tis-2-Web. Technician will also perform an oil consumption test by following the latest version of bulletin 01-06-01-011. |
| PIP5078 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician that service replacement engine part number 12655766 may be received when a service replacement engine is ordered. Technician will need to part off the original engine. |
| PIP5095B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP5029E | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:MECHANICAL. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIP5163 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| 06-06-01-010C | 2017-08-15. Service bulletin. ENGINE. This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period. |
| PIP5226 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings. |
| PIP5216 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:MECHANICAL. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP5163A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5203 | 2017-08-15. Service bulletin. POWER TRAIN; ENGINE. This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors. |
| PIP4716F | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; STEERING:HYDRAULIC POWER ASSIST SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that may have a short, sharp rattle noise from the front of the engine at start up. Technician may find Diagnostic Trouble Codes P0011 P0014 P0016 or P0017. Technician will need to inspect the engine belt. If the vehicle is equipped with a hydraulic power steering, technician will need to verify the power steering pulley outer edge is aligned flush with shaft and repair as needed. If pulley alignment is correct or vehicle does not have hydraulic steering, replace the engine belt. If the noise is still present and it is coming from the cam actuators they will need to be replaced. |
| PIP5093A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that may have an engine oil leak that appeared as they were driving the vehicle in extremely cold ambient temperatures. The technician may find the oil leak is coming from the rear main seal. Technician will need to check for proper thermostat operation by following thermostat Diagnosis as outlined in Service Information and replace the thermostat as necessary. Also the technician will remove the cam cover, inspect the positive crankcase ventilation baffle inside, and replace the cam cover if obvious sludge build up is present. Any debris in the positive crankcase ventilation pipes, hoses, the positive crankcase ventilation nipple on the cam cover, and the throttle body should be cleaned out. Technician should inspect the related positive crankcase ventilation hoses/connections for potential damage and replace if necessary. Run the engine at operating temperature for 15 minutes at idle. Then turn the engine off, and drain the engine oil for at least 15 minutes to remove all oil and condensation or water from the crankcase. Follow Service Information repair procedures to repair any oil leaks that were induced as a result of the frozen positive crankcase ventilation system and excessive crankcase pressure. Technician should insure the Engine Control Module calibrations have been installed to adjust the engine oil life monitor to a maximum of 7,500 miles (12,070 KM) as well. |
| PIP4670D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles. |
| PIP4919B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal. |
| PIP4924D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp on and a misfire. Technician may find Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P2146, P2149, P2152, P2155, P216A, and or P216D. Technician will need to inspect the fuel injector wiring harness for rub through or internal wire opens. If this concern is found repair or replace the injector harness as needed. |
| PIP4384H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician with a supplement to the Service Information timing procedure for the high feature V-6 engine. Technician will also review the training video on the Common Training Website. |
| PIP4964C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution. |
| PIP4919A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal. |
| PIP5180 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve. |
| PIP5187 | 2017-08-15. Service bulletin. ENGINE; EXTERIOR LIGHTING. This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp on after the Cylinder Head was replaced. If the technician finds Diagnostic Trouble Code P0174 and the replacement head had fuel injectors already installed, the replace the fuel rail with the original fuel rail off the car. |
| PIP4919C | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal. |
| PIP5191 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.