WenmarOpen by Wenmar Pro

Service bulletins for the 2012 Chevrolet Cruze

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1816 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
GCUS-9-26292017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 38170 - Special Coverage. The accelerator pedal can break at the stalk just below the housing due to the driver entering or exiting the vehicle with their foot resting on the accelerator pedal. If the pedal breaks, it would not be possible to operate the accelerator once the stalk has broken off. The vehicle would return to idle regardless of transmission gear position. If this condition occurs within the stated terms dealers will replace the accelerator pedal.
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4653E2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
PIP5049A2017-11-14. Service bulletin. POWER TRAIN. This PI communicates to the dealer that a shift tower assembly can be replaced to correct a sloppy feel in the shift lever instead of replacing a complete transmission assembly.
09-07-30-018C2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
PI0770C2017-10-12. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary informational bulletin provides a procedure to replace the RH and LH front drive shaft for conditions of a wobble felt in vehicle acceleration from stop through 1-2 shift
16-NA-3382017-08-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
PIP5242A2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). This Preliminary Information communication provides information to the technician about vehicles that have a squeak noise when operating the clutch pedal. Technician will need to contact General Motors Technical Assistance Center for further assistance.
PIP52422017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). This Preliminary Information communication provides information to the technician that before calling General Motors Technical Assistance Center for assistance, there is some basic diagnostic information that must be obtained in order for General Motors Technical Assistance Center to provide proper direction in repairing the vehicle. Technician should use published Service Information vibration diagnostics, Pico scope, and Vibration Analysis Worksheet found in the Latest Version of Bulletin 03-00-91-001.
PIT54422017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PI0324E2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary information bulletin provides information on doing a pressure line test prior to replacement and removal of the transmission for conditions relating to No Forward, No Reverse, No Crank, Engine Cranks But Will Not Start.
PI15212017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; STEERING; POWER TRAIN. This preliminary informational bulletin provides repair information to correct a customer concern of loss of power steering assist, hard to steer, and/or "Service Power Steering" message on in DIC.
PI14682017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). This preliminary informational bulletin provides repair information to correct a customer concern of a squeak noise heard when operating the clutch pedal.
PI0421D2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). This preliminary informational bulletin provides repair information to correct a customer concern of a fluid leak from under the front of the vehicle, the clutch pedal is hard to push, returns slow, does not return all the way to the top or does not return at all.
PI0950A2017-08-15. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES; POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary informational bulletin provides repair information to correct a customer concern of on an automatic transmission fluid leak.
06-00-89-026L2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
PIP51502017-08-15. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a rattle or knock noise from the engine transmission area when starting the vehicle. Technician will need to verify that noise is not engine related by following "Engine Noise on Start-up, but only lasting a few seconds" diagnostic in Service Information. Technician should be advised that Engineering has identified that the starter motor is rotating the crankshaft at a speed that excites the dual mass flywheel springs and is the root cause of the noise.
PIP4112M2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4112L2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP5043A2017-08-15. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that have a grind growl noise on the 1-2 shift that can be felt in the clutch pedal and brake pedal if applied during a 1-2 shift under light or normal acceleration. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP5050A2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that have a vibration that is only present in fourth gear when lugging the engine. Technician will need to contact General Motors Technical Assistance Center if the vibration is fourth gear only verify correct shift system adjustment and if no change.
PIT5076C2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT:ELECTRICAL; STEERING:ELECTRIC POWER ASSIST SYSTEM. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIP5150A2017-08-15. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that have a rattle or knock noise from the engine transmission area when starting the vehicle. Technician will need to verify that noise is not engine related by following "Engine Noise on Start-up, but only lasting a few seconds" diagnostic in Service Information. Technician should be advised that Engineering has identified that the starter motor is rotating the crankshaft at a speed that excites the dual mass flywheel springs and is the root cause of the noise.
PIP4112N2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4990A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles with the service engine soon lamp that comes on. Technician may find Diagnostic Trouble Code U0101. Technician should review the appropriate Service Information diagnostics for DTC U0101. Also gather all other diagnostic trouble codes in the vehicle and which modules they are set in. The transmission connector pins should be checked for damaged terminals or poor terminal fit. Also inspect the under hood fuse block for damaged terminals or poor terminal fit and mis-positioned fuses in fuse block. Inspect the ground for the Transmission Control Module. Technician should refer to Service Information automatic transmission controls schematics to determine the ground identification.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.