WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Camaro

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1600 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
06-00-89-031C2017-12-22. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
030729004I2017-12-22. Service bulletin. POWER TRAIN. This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
040310013I2017-12-22. Service bulletin. POWER TRAIN. This informational bulletin provides information on driving characteristics of rear wheel drive vehicles and winter tires, tire responses to road conditions and application tips.
140420001A2017-12-22. Service bulletin. POWER TRAIN. This information bulletin provides a procedure to add a friction modifier to the rear differntial in the customers concern is a moan from the rear diff during slow and tight maneuvers.
PI0137E2017-12-22. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This preliminary bulletin provides a procedure to repair the rear axle seals to correct the customers concern of a chatter or moan on low speed turns.
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
16-NA-3382017-08-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
16-NA-1752017-08-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 48 and 104 KM/H (30 and 65 MPH) at a steady state.
PIT54422017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PIP5097A2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides the technician with the following steps to correct a moan noise from the rear axle during cold turning maneuvers. This noise might start to be noticed as the vehicle accumulates over 3000 miles. The technician is to perform the following steps. 1. With original lube in axle, conduct Freeway Speeds for 10 miles to warm up lube. 2. Immediately drain original lube and refill with fresh lube. 3. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 4. . In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 5. Perform 4 Figure 8?s at (5-10 mph). 6. Freeway Speeds for 20 miles until operating temperature is achieved. 7. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 8. In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 9. Perform 4 Figure 8?s at (5-10 mph). 10. Immediately drain current lube in axle and refill with fresh lube. 11. Perform Steps 3 thru 9 again. 12. Immediately drain current lube in axle and refill with fresh lube. Proceed with steps 2 through 9 two times, for a total of 3 drain and fill procedures. This should only be done for a moan noise from the rear axle during cold start turning maneuvers. During regular maintenance the fluid only needs to be changed one time.
PI0486B2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). This preliminary bulletin provides a procedure to replace the clutch pedal assembly due to thermal contraction of the clutch fluid and to correct the customers concern of the pedal feels low or doesn?t return.
PI1344A2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY. This preliminary bulletin provides a procedure to remove and inspect the clutch select solenoid valve for damage, located in the valve body to correct the customers concern of reduced acceleration at low speeds and trans slip at lauch.
PI13602017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary bulletin provides a procedure to perform a transmission inspection and adjustment before having to replace the parking pawl actuator if the inspection found no problem.
PI0486C2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). This technical bulletin provides a procedure to replace the clutch pedal assembly to correct a customer concern of low clutch pedal or that the clutch pedal does not fully return to the top after being depressed caused by imbalance in pressure forces due to thermal contraction of clutch fluid.
16-NA-1752017-08-15. Service bulletin. POWER TRAIN. This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
PIE0327A2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This engineering information bulletin annouces the end of need for information from the field regarding intermittent difficulty shifting, transmission leak and/or possible DTCs set.
PI1360C2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH. This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
PI1360B2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH. This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
PIE03272017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES; POWER TRAIN. This engineering information bulletin is requesting information from dealers on a customer concern of intermittent difficulty shifting, transmission leak and/or possible DTCs set.
16-NA-0142017-04-11. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE STATOR SHAFT SUPPORT TO CORRECT CUSTOMER CONCERN ON A DELAYED ENGAGEMENT WHEN THE TRANSMISSION IS SHIFTED FROM PARK TO REVERSE OR PARK TO DRIVE AFTER THE VEHICLE HAS BEEN SITTING WITH THE ENGINE OFF DUE TO THE TORQUE CONVERTER DRAINING THE TRANSMISSION FLUID BACK INTO THE TRANSMISSION PAN.
PIP-4554-M2016-08-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH THE STEPS ON REPAIRING A CLUNK NOISE AFTER SHIFTING FROM REVERSE TO DRIVE OR DRIVE TO REVERSE AND THEN ACCELERATING. THE CONCERN IS ONLY WITH REAR WHEEL DRIVE 6L45 OR 6L50 AUTOMATIC TRANSMISSIONS WITH REGULAR PRODUCTION OPTION CODE MYA OR MYB APPLY. APPLY THREAD LOCKER TO THE TRANSMISSION OUTPUT SHAFT FLANGE SPLINES AND INSTALL A NEW FRONT PROPELLER SHAFT FLANGE NUT. APPLY THREAD LOCKER TO THE NEW PROPELLER SHAFT FLANGE NUT IF IT DOES NOT CONTAIN A PRE-APPLIED ADHESIVE PATCH.
SB-16-NA-1302016-08-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO INSPECT THE UPPER VALVE BODY TO DETERMINE THE CORRECT RPO USAGE TO CORRECT A CONCERN THAT AFTER INSTALLATION OF A REPLACEMENT UPPER VALVE BODY, THE TRANSMISSION MAY HAVE NO REVERSE AND NO 2ND GEAR DUE TO THE INSTALLATION OF THE INCORRECT UPPER VALVE BODY.
SB-03-07-29-004K2016-08-06. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION. THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
PI1344B2016-07-07. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some customers may comment that the vehicle has reduced acceleration at low speed and/or transmission is slipping from a launch. Technicians may find DTC P0751 set or stored in history. This condition may be caused by the Clutch Select Solenoid Valve 2 (359), located in the lower valve body, sticking in its bore resulting in a 4th gear start. Note: This condition can be very intermittent and difficult to duplicate.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.