Service bulletins for the 2007 Cadillac SRX
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
909 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Transmission and driveline are shown. Show all
| 13-08-116-001A | 2018-04-23. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; POWER TRAIN; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected tampering. |
|---|---|
| 09-06-04-026G | 2018-04-23. Service bulletin. ENGINE; POWER TRAIN. This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2) |
| 12-07-30-001B | 2018-04-16. Service bulletin. POWER TRAIN. This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case. |
| 030729004I | 2017-12-22. Service bulletin. POWER TRAIN. This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises. |
| 120310002 | 2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles |
| PIP4112P | 2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIP4554K | 2017-12-22. Service bulletin. POWER TRAIN. This Preliminary Information communication provides the technician with the steps on repairing a clunk noise after shifting from reverse to drive or drive to reverse and then accelerating. The concern is only with rear wheel drive 6L45 or 6L50 automatic transmissions with Regular Production Option Code MYA or MYB apply. Apply thread locker to the transmission output shaft flange splines and install a new front propeller shaft flange nut. Apply thread locker to the new propeller shaft flange nut if it does not contain a pre-applied adhesive patch. |
| 09-07-30-018C | 2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions |
| 10-04-20-001F | 2017-08-15. Service bulletin. POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT. This technical bulletin provides a procedure to replace the rear differential fluid if the rear axle has a clunk or chatter noise on turns. |
| PIC5460B | 2017-08-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles with a no crank concern or they are unable to remove their key from the ignition lock cylinder may find Diagnostic Trouble Codes P0318, P1629, U1040, U1064, U1153, U1192, and U1300 stored in the Engine Control Module. Other Class 2 modules may have a U0100 and/or U1000 code stored. These concerns may be caused by an Ignition 1 Power Feed (circuit 5290) or Class 2 (circuit 1807) wiring concern to the Engine Control Module. If the electrical center ignition relay feedback parameter in the Engine Control Module is not battery voltage, measure the voltage at the Engine Control Module fuse in the under-hood fuse block. If voltage is less than battery voltage, check to make sure the Power Control Module is turning the relay on via circuit 5069. If there is battery voltage at the Engine Control Module fuse, check Ignition 1 (circuit 5290) between the fuse and the Engine Control Module. If Ignition 1 (circuit 5290) to the Engine Control Module checks ok, check for a possible open in the Class 2 (circuit 1807) to the Engine Control Module. If all connections and wiring are OK, suspect a possible relay or an ECM concern. |
| 02-07-30-052J | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES. This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®. |
| 06-00-89-026L | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| PIP4112M | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIP4112L | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIC4740D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon light is on, Reduced engine power message, no crank, multiple warning lights on, transmission shifts hard, or the door locks cycle while driving. The Transmission Control Module or Engine Control Module may not communicate. With Diagnostic Trouble Codes C0242, C0561, P0575, P0615, P0700, P0856, P1629, P2544, U0073, U0074, U0100, U0109, U0121, U0140, U2100, U2105, and / or U2106 stored. The technician is to inspect the transmission X1 connector terminals for loose or poor fit. Disconnect the X1 connector and carefully tug on each wire to insure pins are fully seated. A side load on the wires may also cause a false positive lock. Technician is to repair the connections as necessary. |
| PIC4740C | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:WIRING. This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon light is on, Reduced engine power message, no crank, multiple warning lights on, transmission shifts hard, or the door locks cycle while driving. The Transmission Control Module or Engine Control Module may not communicate. With Diagnostic Trouble Codes C0242, C0561, P0575, P0615, P0700, P0856, P1629, P2544, U0073, U0074, U0100, U0109, U0121, U0140, U2100, U2105, and / or U2106 stored. The technician is to inspect the transmission X1 connector terminals for loose or poor fit. Disconnect the X1 connector and carefully tug on each wire to insure pins are fully seated. A side load on the wires may also cause a false positive lock. Technician is to repair the connections as necessary. |
| PIP3720D | 2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design. |
| PIP4554H | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides the technician with the steps on repairing a clunk noise after shifting from reverse to drive or drive to reverse and then accelerating. The concern is only with rear wheel drive 6L45 or 6L50 automatic transmissions with Regular Production Option Code MYA or MYB apply. Apply thread locker to the transmission output shaft flange splines and install a new front propeller shaft flange nut. Apply thread locker to the new propeller shaft flange nut if it does not contain a pre-applied adhesive patch. |
| PIP4112N | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIP4554J | 2017-08-15. Service bulletin. WHEELS; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN. This Preliminary Information communication provides the technician with the steps on repairing a clunk noise after shifting from reverse to drive or drive to reverse and then accelerating. The concern is only with rear wheel drive 6L45 or 6L50 automatic transmissions with Regular Production Option Code MYA or MYB apply. Apply thread locker to the transmission output shaft flange splines and install a new front propeller shaft flange nut. Apply thread locker to the new propeller shaft flange nut if it does not contain a pre-applied adhesive patch. |
| PIP-4554-M | 2016-08-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH THE STEPS ON REPAIRING A CLUNK NOISE AFTER SHIFTING FROM REVERSE TO DRIVE OR DRIVE TO REVERSE AND THEN ACCELERATING. THE CONCERN IS ONLY WITH REAR WHEEL DRIVE 6L45 OR 6L50 AUTOMATIC TRANSMISSIONS WITH REGULAR PRODUCTION OPTION CODE MYA OR MYB APPLY. APPLY THREAD LOCKER TO THE TRANSMISSION OUTPUT SHAFT FLANGE SPLINES AND INSTALL A NEW FRONT PROPELLER SHAFT FLANGE NUT. APPLY THREAD LOCKER TO THE NEW PROPELLER SHAFT FLANGE NUT IF IT DOES NOT CONTAIN A PRE-APPLIED ADHESIVE PATCH. |
| SB-16-NA-130 | 2016-08-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO INSPECT THE UPPER VALVE BODY TO DETERMINE THE CORRECT RPO USAGE TO CORRECT A CONCERN THAT AFTER INSTALLATION OF A REPLACEMENT UPPER VALVE BODY, THE TRANSMISSION MAY HAVE NO REVERSE AND NO 2ND GEAR DUE TO THE INSTALLATION OF THE INCORRECT UPPER VALVE BODY. |
| SB-03-07-29-004K | 2016-08-06. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION. THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION. |
| SB-10-04-20-001E | 2013-06-25. Service bulletin. POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT. CADILLAC: REAR AXLE IS MAKING A CHATTER NOISE DURING TURNING. MAY ALSO MAKE A CLUNKING SOUND DURING TURNING AS WELL. *KB |
| SB-10287-B | 2012-04-30. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). GM: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. PREMATURE TIMING CHAIN WEAR- REPROGRAM ENGINE CONTROL MODULE. VEHICLES EQUIPPED WITH A HFV6 ENGINE, UNDER CERTAIN DRIVING CONDITIONS, AND WITH EXTENDED OIL CHANGE INTERVALS, THE TIMING CHAIN COULD WEAR PREMATURELY AND CAUSE THE ILLUMINATION OF THE SERVICE ENGINE SOON LIGHT. *JS |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.