Service bulletins for the 2007 Cadillac SRX
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
909 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Automatic transmission are shown. Show all
| 16-NA-130 | 2023-03-08. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:VALVES/VALVE BODY. This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. |
|---|---|
| 06-00-89-031D | 2021-09-07. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN; ENGINE. OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification |
| 150089004C | 2021-03-08. Service bulletin. SUSPENSION:FRONT:MACPHERSON STRUT; SUSPENSION:FRONT:SHOCK ABSORBER; POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT. This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. |
| 1308116001F | 2020-12-07. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION. The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. |
| 09-07-30-018D | 2018-06-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT. This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation. |
| 01-00-89-010J | 2018-05-21. Service bulletin. ENGINE; SERVICE BRAKES; EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION. This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year. |
| PI0938A | 2018-05-21. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic control issues. |
| 01-07-30-042H | 2018-05-21. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; POWER TRAIN. This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition. |
| 120310002 | 2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles |
| 09-07-30-018C | 2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions |
| 02-07-30-052J | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES. This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®. |
| PIP4112M | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIP4112L | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIC4740D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon light is on, Reduced engine power message, no crank, multiple warning lights on, transmission shifts hard, or the door locks cycle while driving. The Transmission Control Module or Engine Control Module may not communicate. With Diagnostic Trouble Codes C0242, C0561, P0575, P0615, P0700, P0856, P1629, P2544, U0073, U0074, U0100, U0109, U0121, U0140, U2100, U2105, and / or U2106 stored. The technician is to inspect the transmission X1 connector terminals for loose or poor fit. Disconnect the X1 connector and carefully tug on each wire to insure pins are fully seated. A side load on the wires may also cause a false positive lock. Technician is to repair the connections as necessary. |
| PIC4740C | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:WIRING. This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon light is on, Reduced engine power message, no crank, multiple warning lights on, transmission shifts hard, or the door locks cycle while driving. The Transmission Control Module or Engine Control Module may not communicate. With Diagnostic Trouble Codes C0242, C0561, P0575, P0615, P0700, P0856, P1629, P2544, U0073, U0074, U0100, U0109, U0121, U0140, U2100, U2105, and / or U2106 stored. The technician is to inspect the transmission X1 connector terminals for loose or poor fit. Disconnect the X1 connector and carefully tug on each wire to insure pins are fully seated. A side load on the wires may also cause a false positive lock. Technician is to repair the connections as necessary. |
| PIP4554H | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides the technician with the steps on repairing a clunk noise after shifting from reverse to drive or drive to reverse and then accelerating. The concern is only with rear wheel drive 6L45 or 6L50 automatic transmissions with Regular Production Option Code MYA or MYB apply. Apply thread locker to the transmission output shaft flange splines and install a new front propeller shaft flange nut. Apply thread locker to the new propeller shaft flange nut if it does not contain a pre-applied adhesive patch. |
| PIP4112N | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear. |
| PIP4554J | 2017-08-15. Service bulletin. WHEELS; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN. This Preliminary Information communication provides the technician with the steps on repairing a clunk noise after shifting from reverse to drive or drive to reverse and then accelerating. The concern is only with rear wheel drive 6L45 or 6L50 automatic transmissions with Regular Production Option Code MYA or MYB apply. Apply thread locker to the transmission output shaft flange splines and install a new front propeller shaft flange nut. Apply thread locker to the new propeller shaft flange nut if it does not contain a pre-applied adhesive patch. |
| PIP-4554-M | 2016-08-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH THE STEPS ON REPAIRING A CLUNK NOISE AFTER SHIFTING FROM REVERSE TO DRIVE OR DRIVE TO REVERSE AND THEN ACCELERATING. THE CONCERN IS ONLY WITH REAR WHEEL DRIVE 6L45 OR 6L50 AUTOMATIC TRANSMISSIONS WITH REGULAR PRODUCTION OPTION CODE MYA OR MYB APPLY. APPLY THREAD LOCKER TO THE TRANSMISSION OUTPUT SHAFT FLANGE SPLINES AND INSTALL A NEW FRONT PROPELLER SHAFT FLANGE NUT. APPLY THREAD LOCKER TO THE NEW PROPELLER SHAFT FLANGE NUT IF IT DOES NOT CONTAIN A PRE-APPLIED ADHESIVE PATCH. |
| SB-16-NA-130 | 2016-08-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO INSPECT THE UPPER VALVE BODY TO DETERMINE THE CORRECT RPO USAGE TO CORRECT A CONCERN THAT AFTER INSTALLATION OF A REPLACEMENT UPPER VALVE BODY, THE TRANSMISSION MAY HAVE NO REVERSE AND NO 2ND GEAR DUE TO THE INSTALLATION OF THE INCORRECT UPPER VALVE BODY. |
| SB-10287-B | 2012-04-30. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). GM: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. PREMATURE TIMING CHAIN WEAR- REPROGRAM ENGINE CONTROL MODULE. VEHICLES EQUIPPED WITH A HFV6 ENGINE, UNDER CERTAIN DRIVING CONDITIONS, AND WITH EXTENDED OIL CHANGE INTERVALS, THE TIMING CHAIN COULD WEAR PREMATURELY AND CAUSE THE ILLUMINATION OF THE SERVICE ENGINE SOON LIGHT. *JS |
| SB-09-07-30-014A | 2011-03-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. CADILLAC: RUMBLE, GRIND, TICKING OR RATTLE TYPE NOISE WHILE DRIVING, OUTPUT SHAFT SPALLING (REPLACE OUTPUT SHAFT AND BEARING). *PE |
| PIP4333 | 2008-04-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). DTC'S P0011, P0014, P0021, P0024, P0341, P0346, P0366, OR P0391. WITH 3.6 LY7 OR LLT. *NJ |
| 07-07-30-032 | 2008-03-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL). SHIFTER BINDS, IGNITION KEY STICKS, [SHIFT TO PARK] MESSAGE DISPLAYED ON DRIVER INFORMATION CENTER (DIC), DEAD BATTERY (ADJUST SHIFT LINKAGE). *NJ |
| 4052 | 2007-09-27. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 2-3 UPSHIFT SLIP OR FLARE. *KB |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.