WenmarOpen by Wenmar Pro

Service bulletins for the 2012 Buick LaCrosse

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1830 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
PIP5232A2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP52322018-05-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP3333C2018-05-07. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent engine misfire and a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0300, P0301, and/or P0304. Technician will need to follow published Service Information diagnostics first. If the Service Information diagnostics do not isolate a cause for this concern, inspect the inside of the fuel rail and/or fuel tank for fuel contamination. f fuel contamination is present, refer to the "Fuel System Cleaning" procedure in Service Information. Dealer will need to advise the customer to only use fuel from high quality high volume Top Tier fuel stations.
12-06-01-009E2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin advises the technician of new timing chains and guides and part numbers.
13-06-01-0032018-04-23. Service bulletin. ENGINE. This technical bulletin provides a replacement for PIP5025F to advise engine replacement is no longer necessary if "zebra stripes" are present and to outline a related repair procedure.
09-06-04-026G2018-04-23. Service bulletin. ENGINE; POWER TRAIN. This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
12-06-01-009C2018-04-23. Service bulletin. ENGINE. This informational bulletin provides information for installing a camshaft timing chain kit on the high feature V6.
12-06-01-009B2018-04-23. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS. This informational bulletin provides information for installing a camshaft timing chain kit on the high feature V6.
150089005A2018-04-23. Service bulletin. EQUIPMENT; ENGINE. This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
16NA2492018-04-23. Service bulletin. ENGINE. Low Audible Whine Noise has been found to be transmitting from the balance shaft drive chain.
12-06-01-009A2018-04-16. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE. This informational bulletin provides information on high feature V6 timing chains kits and chain guide replacements.
13-06-01-003B2018-04-02. Service bulletin. ENGINE. This technical bulletin provides a procedure for oil consumption test and set up including piston, connecting rod and bearing due to excessive oil consumption and/or need to add oil between oil changes.
PIP5095E2018-03-12. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP5226B2018-02-21. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5540A2018-02-21. Service bulletin. ENGINE. This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP3535C2018-01-16. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication informs dealer technicians of a potential whining noise that can occur after servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.
PIP4959G2018-01-16. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
01-06-01-011I2017-12-22. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
PI0562E2017-12-22. Service bulletin. ENGINE. This preliminary informational bulletin provides a procedure to reprogram the ECM for concerns regarding a loud rattle noise on start up that stops in 3 seconds or less.
00-06-01-026H2017-12-22. Service bulletin. ENGINE. This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP5096B2017-12-22. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles with a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P011, P0014, P0021, and or P0024. During inspection if no other drivability concerns found inspect the engine EUN sticker for an (A) before the sequence number. If there is an "A" before the sequence number then replace the OCV/Cam Actuator Solenoid Valve with a replacement "service" valve.
GCUS-9-9392017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. 14582 - Special Coverage. On some 2008 model year (MY) Saturn Outlook; 2008-2009 MY Buick Allure, Chevrolet Equinox, Chevrolet Uplander, Pontiac G8, Pontiac Montana SV6, Pontiac Torrent, and Saturn VUE; 2008-2010 MY Hummer H3 and Pontiac G6; 2008-2011 MY Cadillac CTS, Cadillac SRX, and Chevrolet Impala; 2008, 2011-2012 MY Chevrolet Captiva; 2008-2012 MY Buick Enclave, Buick Lacrosse, Chevrolet Colorado, Chevrolet Malibu, and GMC Canyon; 2009 MY Hummer H3T; 2009-2011 MY Buick Lucerne; 2009-2012 MY Chevrolet Traverse and GMC Acadia; and 2010-2012 MY Buick Regal vehicles, the throttle-position sensor may cause the engine to run rough, cause the malfunction-indicator lamp and/or an engine reduced power message to illuminate, and reduce the engine's power. Dealers are to replace the throttle body assembly and gasket for Bosch equipped vehicles, or to install the throttle position sensor kit for Hitachi equipped vehicles. The Hitachi throttle body assembly only needs to be replaced if the sensor kit does not correct the condition. The repairs will be made at no charge to the customer. For vehicles covered by Vehicle Service Contracts, all eligible claims with repair orders on or after September 24, 2015, are covered by this special coverage and must be submitted using the labor operation codes provided with this bulletin. Claims September 2015 Bulletin No.: 14582 with repair orders prior to September 24, 2015, must be submitted to the Service Contract provider.
PIP55282017-11-14. Service bulletin. ENGINE. This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
09-06-04-026E2017-10-12. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.