WenmarOpen by Wenmar Pro

Service bulletins for the 2016 BMW X6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

241 on file from NHTSA, as of 2026-10-19.

By type

By component

By topic

Bulletins, newest first
B6123152018-11-13. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. "The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations. We recommend using ""BMW Group approved"" washer fluid when servicing the vehicle or performing repairs on the windshield washer system. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates. If the correct washer fluid is being used, diagnose the system using normal troubleshooting with ISTA. A fault code may be stored if an electrical fault occurs in the circuit. PARTS INFORMATION Part NumberDescriptionQuantity83 19 2 406 220BMW WWS Cold Weather Concentrate 35% 55 GalAs needed83 19 2 361 205BMW Windshield Washer Concentrate 1 GalAs neededNote: As applicable, do not exceed your state's maximum for the allowable amount/percentage of ""Washer Concentrate"" that can be used when mixing the windshield washer fluid solution. WARRANTY INFORMATION The issue described in this bulletin is not a vehicle-related defect in materials or workmanship. If a vehicle repair is required as a result of this issue, it is are not claimable under a BMW limited warranty."
B3405152018-11-13. Service bulletin. SERVICE BRAKES. Ticking Noise from the Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
B6608152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Comfort Access Does Not Function After Vehicle Enters Sleep Mode. Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.
B6509152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6210152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. "Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 ""display backlighting and graphics PCB switched off"" stored. Kombi software."
B6207152018-11-13. Service bulletin. ELECTRICAL SYSTEM. "Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles ""arriving"" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed ""prior"" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2. "
B6207152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster display is partially blank. The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.
B3601152018-11-13. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B6204152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:SOFTWARE. Service Action: Programming Control Units. Sporadically the vehicle cannot be started, due to a discharged battery caused by a software glitch in the instrument cluster.
B3601152018-11-13. Service bulletin. TIRES; WHEELS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B8405142018-11-13. Service bulletin. EQUIPMENT. One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
6513122018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT. This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
1238142018-11-13. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE. SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
1209152018-11-13. Service bulletin. VEHICLE SPEED CONTROL; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. "SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the ""fuel consumption, current"" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold."
B6205162018-11-13. Service bulletin. ELECTRICAL SYSTEM. Head-up Display is no Longer Visible. HUD (Head-up Display) adjusted to the lowest position is no longer visible. Software in the instrument cluster
B3405152018-11-13. Service bulletin. SERVICE BRAKES. Ticking Noise from the Front Axle When Cornering This Service Information bulletin supersedes SI B34 05 15 dated December 2015. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
B6119152018-11-05. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; STEERING:COLUMN; STEERING. Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
B3601152018-11-05. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B3404142018-11-05. Service bulletin. SERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC. Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
B2704152018-11-05. Service bulletin. POWER TRAIN:DRIVELINE; WHEELS. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B6510152018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
B6111152018-11-05. Service bulletin. SEATS; SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; ELECTRICAL SYSTEM. Rear Seat Heater Inoperative. The front passenger and both rear seat heaters do not work. The following fault codes are stored in the BDC (Body Doman Controller): D90C18 - LIN master I: Short circuit D90C1A - LIN master I: Communication faulty CAUSE One of the rear seat heater modules has an internal fault, which interrupts LIN bus communication.
B5116152018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
B3408142018-11-05. Service bulletin. POWER TRAIN:AXLE ASSEMBLY; WHEELS:HUB; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC. Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
B3201152018-11-05. Service bulletin. STEERING:COLUMN; STEERING. Noise When Adjusting the Steering Column Up or Down. Creaking noise when raising or lowering the steering column position CAUSE Steering column adjustment

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.