WenmarOpen by Wenmar Pro

Service bulletins for the 2008 BMW X5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

245 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
B1117152018-12-10. Service bulletin. ENGINE; EQUIPMENT. "N63, N63TU and N63R Engines: Upper Oil Pan Removal and Installation Repair Instructions This Service Information bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
B1109162018-12-10. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:BELL HOUSING; POWER TRAIN. N63, N63TU, S63 and S63TU Engines: Oil Leak from the Rear of the Engine and Transmission Bell Housing. Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.
B1106162018-12-10. Service bulletin. EQUIPMENT; ENGINE. N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
B1211162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. ISTA/P Cannot Program an E-Series N55 Replacement DME. ISTA/P fails when attempting to program a replacement DME (MEVD172) on BN2000 E-Series vehicles with the Continental HPP. Part number: 12 14 8 618 483. DME logistic error between the replacement hardware and basic software prevents correct programming with ISTA/P.
B1106162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING. N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
B0105112018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE. "SI B01 05 11 March 2016 Warranties This Service Information bulletin supersedes SI B01 012 11 dated December 2012. Please read this Service Information bulletin in its entirety: the part information and content format has been completely updated. designates changes to this revision SUBJECT N52K Tank Leak Diagnostic Module (DMTL) Pump: Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the tank leak diagnostic module (DMTL) pump to: 10 years/120,000 miles as determined by the vehicle's original in-service date Item #3: This ""componentspecific"" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Note: For items #1, #2 and #7, please refer to the ""Parts Information"" section. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Even though this is NOT a Recall, BMW NA has sent VIN-specific customer notification letters (examples attached)."
B8403142018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
B6502162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B0703142018-12-10. Service bulletin. ENGINE; STEERING; ELECTRICAL SYSTEM; EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6507092018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
B1308152018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS; ENGINE. The high-pressure injectors may fail, resulting in an engine malfunction warning and reduced engine output.
6522122018-12-03. Service bulletin. EQUIPMENT. Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
6501102018-12-03. Service bulletin. EQUIPMENT. "CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
1607122018-12-03. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. Service Action: Replace the Left and Right Fuel Level Sensor. After refueling, the fuel gauge will display an incorrect fuel level. When this occurs, the fuel gauge shows the fuel level as 3/4 full. CAUSE Due to a high proportion of ethanol in the fuel, the internal mechanisms of the fuel level sensors may swell. This may inhibit the movement of one or both of the fuel level sensors.
0105112018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE. ?BMW has become aware of a potential problem with the durability of the Tank Leak Diagnostic Module (DMTL) pump on MY 2007, 2008 and 2009 BMW X5 vehicles equipped with the N52K engine. A small percentage of these vehicles will actually develop this problem. Some of the affected vehicles will have the Service Engine Soon lamp illuminated, but the vehicle?s drivability and engine performance will not be reduced by this DMTL pump malfunction.
6515122018-12-03. Service bulletin. EQUIPMENT. "Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
6113052018-12-03. Service bulletin. ELECTRICAL SYSTEM. "Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
3101122018-12-03. Service bulletin. POWER TRAIN. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
1607122018-12-03. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. Service Action: Replace the Left and Right Fuel Level Sensor. After refueling, the fuel gauge will display an incorrect fuel level. When this occurs, the fuel gauge shows the fuel level as 3/4 full. CAUSE Due to a high proportion of ethanol in the fuel, the internal mechanisms of the fuel level sensors may swell. This may inhibit the movement of one or both of the fuel level sensors.
1306122018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE. "N63 and N74 Engine: ISTA/D 2.33 Diagnostic Error in the Low-pressure Fuel Supply Sensor Value. INFORMATION When diagnosing the low-pressure fuel supply sensor with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar at all times. * B1214_DI6KNDR * D18KHDR * AT1214_DIKNDR * AT1214_DIKHDR Do not replace the low-pressure fuel supply sensor. The operating pressure of the low-pressure fuel supply sensor can found in ""DME Diagnostic Query"" using the following procedure: 1. Exit the test plan and return to the control unit tree. http://www.bmwtis.net/tiscode/cgi-bin/omcgi.exe?sie_path=/tsb/bulletins/htm_store/14907...11/7/2012 Page 2 of 2 2. Select ""DME"" in the control unit tree. 3. Select "" Call Up ECU Functions."" 4. Select ""Diagnostic Query."" 5. Select ""Fuel Pressure (Low Pressure)."" 6. Select ""Query Status."" The engine must be running to verify operation of the pressure sensor. The software error will be corrected in ISTA/D 2.34, scheduled for release in December 2012. "
1307122018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1107132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N63T Engine: New Test Plan to Check Engine Oil Level with ISTA/D 3.39.21. INFORMATION With the release of ISTA/D 3.39.21, a new test plan is available for checking the engine oil level in some vehicles with the N63T engine. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: * F01 and F02 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F06, F07, F12 and F13 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F10 with the N63T engine produced from 7/2013 and later with I-Level F010-13-07-501 or higher Test plan path: Service Function/Drive/Motor Electronics/Motor Oil/Oil Level IMPORTANT: Do not perform this test plan on the following vehicles: * E70, E71, F01, F02, F04, F06, F07, F12 and F13 vehicles with the N63 or N63T engine, produced before 3/2013 l * F10 vehicles with the N63 engine produced before 7/2013 If this test plan is performed on these vehicles, the result is an incorrect measurement and level indication; overfilling of the engine will occur. Overfilling of the engine will result in engine damage. When a solution for vehicles which are not at one of the integration levels above is available, it will be communicated promptly. WARRANTY INFORMATION Not applicable. [ Copyright (c)2013 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15702.1.B11071... 11/12/2013
5412082018-12-03. Service bulletin. VISIBILITY. Water Leak from the Front of the Sunroof. During extended periods of heavy rain, water may enter the vehicle from the area around the front of the sunroof cassette, the Roof Control Panel (FZD), the map lights, or the A-pillars. The customer may also simply state that the carpet in the front of the vehicle is wet. The sunroof cassette is overflowing due to the fact that one or both of the front sunroof drains are trapped or twisted.
5407102018-12-03. Service bulletin. VISIBILITY. Various Complaints with Panoramic Sunroof.
5136082018-12-03. Service bulletin. VISIBILITY. "Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.