WenmarOpen by Wenmar Pro

Service bulletins for the 2010 BMW X3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

47 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B1106162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING. N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
B6502162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B0703142018-12-10. Service bulletin. ENGINE; STEERING; ELECTRICAL SYSTEM; EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6507092018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
5413092018-12-03. Service bulletin. EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; VISIBILITY:SUN/MOON ROOF ASSEMBLY. "?Panoramic Sunroof Repair Instructions. INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. "
5413092018-11-26. Service bulletin. VISIBILITY. "Panoramic Sunroof Repair Instructions. INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. Refer to the following repair attachments: Front Glass Mechanism repair E53, E61, E70, E83, E91.pdf Rear Glass Mechanism repair E53, E61, E70, E83, E91.pdf Wind Deflector Mechanism repair E53, E61, E70, E83, E91.pdf Sunshade Mechanism repair E53, E61, E83.pdf Sunshade Mechanism repair E70, E91.pdf All panoramic roofs for the above-listed models are conceptually similar and utilize similar repairs. NOTE: An E83 (X3) sunroof cassette is used for demonstration of the repairs. Some differences may exist between this and other models. The following prerequisite work is required in order to replace the following kits (in addition to removing the cassette from the car and glass from the cassette): Front Glass Mechanism - None. Rear Glass Mechanism - Remove the front glass mechanism. Wind Deflector Mechanism - Remove the front glass mechanism; remove the rear glass mechanism. Sun shades and Shade Mechanism - None Sunroof Mechanical 3D Animation: A 3D animation has been developed in order to clarify how the sunroof mechanism operates, as well as how it is assembled and disassembled. To view this animation, open Interactive Career Pathways (ICP) and select ""Replace Front and Rear Glass Panel Mechanic"" from the Technical Service Information section of the home page. This animation allows you to: * Operate the mechanism and view from any angle; * Add or remove parts and then cycle the sunroof; * S
B0116182018-11-26. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. For the above-referenced vehicles with driver?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata driver?s side airbag module in a listed vehicle.
0703142018-11-26. Service bulletin. EQUIPMENT. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
0110142018-11-26. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Engine Camshaft (VANOS) Adjustment Units: Limited Warranty Extension to 10 Years Without Mileage Limitation. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the Camshaft (VANOS) Adjustment Units on certain model BMW vehicles equipped with the non-turbocharged 6-cylinder engine to: 10 years without mileage limitation, as determined by the vehicle's original in-service date. This "component-specific" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable New Vehicle/SAV Limited Warranty's exclusions and limitations, in addition to the vehicle and coverage eligibility requirements. This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem.
6103142018-11-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
6103142018-11-13. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
0104142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
2404132018-11-13. Service bulletin. POWER TRAIN. GM6 - 6L45R: Diagnostic Procedure for Shudder or Vibration Issues. A shudder or vibration can be felt under light acceleration or when driving at constant suburban speeds. This can be most noticeable in the 1700 - 2200 engine rpm range while in 3rd through 6th gears. No faults are stored in the EGS module. CAUSE Changes in the frictional properties of the automatic transmission fluid over time can lead to momentary slipping of the torque convertor lock-up clutch.
B0703142018-11-13. Service bulletin. EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B2704152018-11-05. Service bulletin. POWER TRAIN:DRIVELINE; WHEELS. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B3602152018-11-05. Service bulletin. TIRES:VALVE; WHEELS. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
B0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B2702162018-11-05. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); SERVICE BRAKES, HYDRAULIC. "REPAIRING TRANSFER CASE ACTUATOR (VTG SERVO-MOTOR). The Anti-lock Brakes (ABS), Brakes and Dynamic Stability Control (DSC) warnings are on and there may also be a ""Drivetrain Malfunction"" warning on in the Control Display. There is also an audible clicking noise coming from the transfer case actuator when cycling the ignition. The following fault codes may be stored: (DSC) 5F3A - Clutch gearbox-ECU: clutch is open - rear-wheel drive! (VTG) 5463 - Break mechanics (VTG) 5462 - Error actuator or increased power requirements for clutch (VTG) 5461 - Error actuator control Internal wear to the plastic gears of the transfer case actuator."
B0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6507092018-10-09. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
B6507092018-08-06. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.