WenmarOpen by Wenmar Pro

Service bulletins for the 2013 BMW R 1200 GS

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

119 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SIM0107172022-07-05. Service bulletin. ENGINE AND ENGINE COOLING. The engine?s intake charge-air duct limited warranty extension to 10 years/120,000 miles applies to ?eligible USspecification
B1116142022-05-16. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
MC3201132021-12-13. Service bulletin. ENGINE. BMW Motorrad has ascertained that in rare cases the throttle twistgrip sends an implausible signal to the engine management system when the throttle valve is closed.
MC644653982021-08-23. Service bulletin. ENGINE AND ENGINE COOLING. The hill start control operation may be sporadic.
MC598234152021-05-17. Service bulletin. ENGINE. Oil leak immediately after replacing cylinder head cover seal set.
MC640115042019-09-23. Service bulletin. EQUIPMENT; ENGINE. Ticking noises from the cylinder hood.
MC640115042019-09-23. Service bulletin. EQUIPMENT; ENGINE. Ticking noises from the cylinder hood.
MC21001162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. BMW Motorrad has determined in the course of quality observation that in a few cases clutch fluid may leak between the clutch slave cylinder and the braided stainless steel clutch line. The cause is a burr in the clutch slave cylinder which may damage the gasket of the clutch line. A vehicle with high mileage can show signs of gradual impairment of the clutch function. The separating action of the clutch can worsen gradually over a period of time.
MC548832102018-11-26. Service bulletin. ENGINE. When the throttle is closed, the engine goes into emergency mode.
1307122018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1116142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure to check the engine timing chains for wear and should be completed in conjunction with SI B11 06 14 "N63 Customer Care Package". Performing the test plans identified in the procedure below will detect wear at an early stage and if necessary provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to assure the highest standard of performed repairs.
1107132018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015
1106142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The procedure described in this bulletin should be completed in conjunction with performing SI B11 16 14, N63 Engine: Check the Timing Chain. Perform all recommended, due or qualifying "time-based" maintenance service tasks as directed by the Key Reader/ISPA Light application. Note: The procedure in SI B11 16 14 includes an engine oil and filter change. When applicable, also perform the procedure described in SI B61 30 14, 12-Volt Battery Replacement under the BMW Maintenance Program together with performing the N63 Customer Care Package. After completing all necessary repairs, vehicle needs to be test driven for up to 30 minutes to assure the highest standard of performed repairs.
B1116142018-11-13. Service bulletin. ENGINE. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label."
B1210162018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. "N63T - Drivetrain Malfunction Message after Driving for Several Hours This Service Information bulletin supersedes SI B12 10 16 dated April 2016. ""Drivetrain Malfunction"" message displayed with reduced engine power. Erroneous misfire faults may be stored for cylinders 3 and 6. The situation is most likely to occur after driving for several hours at constant highway speeds with light throttle (low load and low engine speed). Cycling ignition off and back on again clears the ""Drivetrain Malfunction"" warning DME software (plausibility check error)."
B1112162018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. SERVICE ACTION: N63T ENGINE - CHECK AND REPLACE THE CRANKCASE VENTILATION HOSES. The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.
1116142018-11-05. Service bulletin. ENGINE. "This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
B1108152018-11-05. Service bulletin. ENGINE. N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin replaces SI B11 08 15 June May 2017 What's New: Diagnostic tips updated. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption Spark plugs fouled with engine oil and excessive engine oil consumption Excessive engine oil consumption Vehicles with less than 40,000 miles should not be considered for valve seal replacement. All Vehicles: A complete oil consumption test, as described inSI B11 03 13, must be performed first, before replacing the valve seals. Do not remove the intake manifolds to clean the intake valve carbon.
B1303152018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Procedure change: indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B1112162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. ?SERVICE ACTION: SERVICE ACTION: N63T ENGINE CHECK AND REPLACE THE CRANKCASE VENTILATION HOSES What's New: ? Defect Code format updated ? Consequential Additional Repair(s) statement added ? Overlapping Labor Procedure statement added . The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.