Service bulletins for the 2016 BMW i8
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
197 on file from NHTSA, as of 2026-10-19.
By type
By component
By topic
| B512016 | 2018-11-13. Service bulletin. STRUCTURE:BODY:DOOR. Door Will Not Go Up All The Way. The driver's side or passenger's side door may not open to the highest position. Insufficient lifting force from gas pressurized damper spring. |
|---|---|
| B612015 | 2018-11-05. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. "Check Control Messages for the 12 Volt Battery are Displayed. Sporadically, one or more of the following Check Control Messages may be displayed. The vehicle starts without problems and after a key cycle, the messages are gone. ID 229 - ""Charge Battery"" ID 304 - ""Change Battery"" ID 415 - ""Discharge Battery while stationary"" ID 460 - ""Replace Battery"" ID 461 - ""Battery state of charge... %"" Additionally, one or more of the following fault codes may be stored: DME - 213901 ""Power management: reduction or switching off of individual electrical consumers"" BDC - 8040C7 ""IBS: The recharging limit has been reached"" CAUSE Software error in the IBS (Intelligent Battery Sensor)." |
| B611915 | 2018-11-05. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; STEERING:COLUMN; STEERING. Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette. |
| B512015 | 2018-11-05. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Window Regulator Noise when Opening or Closing Side Window. A loud cracking noise from the front door power window regulator occurs when opening or closing the right side or left side window. CAUSE Faulty power window regulator |
| B511715 | 2018-11-05. Service bulletin. FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY. "Check Control Message ""Fuel tank system faulty"" is displayed. The Check Control Message ""Fuel tank system faulty"" is displayed in the instrument cluster. One or more of the following fault codes are stored: ""806010 - Refueling button: button jammed open"" ""21B022 - Information for refueling button, function: jammed open (reported by TFE)"" CAUSE The locking rod for the locking fuel filler flap is disconnected from the central locking system." |
| B360115 | 2018-11-05. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna) |
| B651015 | 2018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment. |
| B511615 | 2018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)." |
| B360315 | 2018-11-05. Service bulletin. SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC; SUSPENSION:REAR; WHEELS. Interference Noise from Wheel Assembly. The customer may complain about: ? A ticking noise from the front axle, and/or ? A chirping noise from the rear axle The noise is noticeable while driving at slow speeds next to concrete road barriers, or in tunnels with the windows open. CAUSE Wheel interface with the brake disc |
| B320215 | 2018-11-05. Service bulletin. STEERING:COLUMN; STEERING. Crackling Noises from Area Around Steering Column. There are crackling noises from the area around the steering column when steering into bends or maneuvering |
| B123214 | 2018-11-05. Service bulletin. ENGINE. "Service Engine Soon (MIL) Lamp Illuminated with No Relevant Faults. INFORMATION If an i3 or i8 is brought in for service with a Service Engine Soon (MIL) lamp illuminated, or with a customer concern that the MIL is intermittently illuminated, troubleshoot with ISTA/D. During diagnosis, refer to the functional description (FUB), Troubleshooting Malfunction Indicator Lamp I01. This document explains the rationale behind what triggers an MIL on an electrified vehicle, as well as some diagnostic hints. If these diagnostics do not lead to a root cause and a solution, continue with the following: ? Do not clear faults with ISTA/D. ? Use the recommended ACTRON OBD scan tool to read out any code (P or U code) that is present. The ACTRON scan tool was sent to BMW centers via the automatic tool shipment program. For more information on this tool, refer to SI B04 18 15. ? Record any and all P/U codes. ? Look up the relevant code[s] in the attached document, SAE_P-Code_List.pdf. This list provides the description for BMW specific P/U codes. ? Match the P/U code[s] to the fault codes stored in the vehicle. Typically the P/U code description is very close to the fault code title. - NOTE: Even though multiple OBD-relevant fault codes may be stored in the vehicle, the P/U code displayed is what triggered the MIL. Therefore, continue diagnostics for the fault code associated with the P/U code displayed. ? If no P/U codes are displayed and ISTA/D diagnostics are inconclusive, submit a TC PuMA case entitled Check Engine Light - No Relevant Faults to either ""BMW i3 Powertrain Components"" or ""i8 Powertrain Components"" for further assistance. -The P code and diagnosis summary should be included in the case." |
| B650915 | 2018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL; EQUIPMENT. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H |
| B610715 | 2018-11-05. Service bulletin. ELECTRICAL SYSTEM. "Charging Stops when Using ""Occasional Use"" Cable. When charging the vehicle with the Occasional Use Cable (OUC), and the charge rate set to ""Min"" in the CID, charging may switch off during the charge cycle. In rare cases, the vehicle may not start the charging cycle at all. The following fault is stored in the Electric Machine Electronics (EME): 0x222843 - charging management: Charging target not reachable (power of charger too low) Updated software is available to prevent this situation from recurring. CAUSE The EME software had a minimum charging power threshold of 600W. On the ""Min"" charge setting in the CID, the target charging current is 6 amps. Therefore, if the available voltage at the wall socket dips below 100 volts at any time, charging will be switched off." |
| B511315 | 2018-11-05. Service bulletin. VISIBILITY; ELECTRICAL SYSTEM. Front Windows Reverse Direction when Being Used. When the customer closes one of the front side windows using the one-touch feature, the window reverses direction and opens automatically. CAUSE Faulty window motor |
| B360215 | 2018-11-05. Service bulletin. TIRES:VALVE; WHEELS. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 |
| B840616 | 2018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL. BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's. |
| B840516 | 2018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT ADAPTIVE/MOBILITY. BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit. |
| B641316 | 2018-11-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. "A/C FAILURE: FC 801252 ELECTRIC A/C COMPRESSOR: INTERNAL FAULT DETECTED. Air conditioning (A/C) failure with IHKA fault code ""801252 - Electric A/C compressor: Internal fault detected"". IHKA software fault in the versions detailed in the following table: ModelISTA/P versionIntegration levelF153.57.3F025-15-11-505F303.57.2F020-15-11-504I01, I123.57.0I001-15-11-501" |
| B513016 | 2018-11-05. Service bulletin. STRUCTURE:BODY:TAILGATE; STRUCTURE:BODY:TRUNK LID. TAILGATE UNINTENTIONALLY OPENS. Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate. |
| B511615 | 2018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS; ENGINE. "Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2" |
| B340616 | 2018-11-05. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING. "DSC ""WHEEL SPEED SENSOR"" FAULT CODES AND MALFUNCTION INDICATOR LAMP- DIAGNOSTIC. 1. DSC's fault codes stored from two different wheel speed sensors (both front or both rear): 4809B0 - wheel speed sensor - front left - drive off recognition faulty and 4809CD - wheel speed sensor - front right - drive off recognition faultyor 4809B9 - wheel speed sensor - rear left - drive off recognition faulty and 480686 - wheel speed sensor - rear right - drive off recognition faulty. 2. Next ignition ON (after above codes stored). a) DME fault can occur:1F054D - drive, safety function: Drive power output reduced, DSC signals implausible and b) Malfunction Indicator Lamp (MIL) may light up. Faulty drive off recognition due to: a towing operation with a raised axle operation of the vehicle on the vehicle hoist operation of the vehicle on the roller test stand DSC diagnosis recognizes implausible wheel speeds, so no control is possible. DME fault is entered on safety grounds since the DSC fault still exists after a terminal change and may only be removed while driving." |
| B630516 | 2018-11-05. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:CONCEALMENT DEVICES. "HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION. Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by ""condensation"" rather than a ""water leak"" into the headlight housing, there will be misting/condensation in ""both headlights.""" |
| B111515 | 2018-11-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE; EQUIPMENT. i8 with B38T Engine: Various Faults Related to Engine Oil Pressure. The engine malfunction warning and the engine oil pressure warning is illuminated. One or more of the following faults are stored in the DME: ? 1C2002 Engine oil pump: pressure too low ? 1C0301 Engine oil pressure regulating valve: Jams in a fully energized position ? 1FB801 Check Control message (ID 212): Engine oil pressure. Stop carefully. |
| B662116 | 2018-11-05. Service bulletin. ENGINE; LANE DEPARTURE: SENSING SYSTEM: OTHER; SERVICE BRAKES. KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle. |
| B652416 | 2018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). "NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes ""without a cash option"" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes ""without cash option"". UPDATE Install new map data." |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.