Service bulletins for the 2010 BMW 535i
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
309 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| B010215 | 2018-12-10. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. "SI B01 02 15 January 2016 Warranties This Service Information bulletin supersedes SI B01 02 15 dated December 2015. designates changes to this revision SUBJECT N54 Engine Fuel Injectors - Limited Warranty Extension to 10 Years/120,000 Miles . INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the fuel injectors to: 10 years/120,000 miles as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks." |
|---|---|
| 121412 | 2018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken. |
| 130712 | 2018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation. |
| 130409 | 2018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (?wet?) with fuel, while the injector tips are covered with a layer of carbon deposit. |
| 121611 | 2018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode). |
| 121712 | 2018-12-03. Service bulletin. ENGINE; POWER TRAIN. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software |
| 010212 | 2018-12-03. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. "BMW NA has agreed to extend the emissions warranties of the turbocharger's wastegate to: ??8 years or 82,000 miles, whichever occurs first, as determined from the vehicle's original in-service date select the ""Vehicle Comment"" button to display the extended coverage information. The terms of the original New Vehicle/SAV Limited Warranty and applicable emissions warranty still apply. BMW NA will not provide warranty coverage to any Settlement Class Member's vehicle containing modifications or alterations to the turbocharger or its wastegates (software, hardware or otherwise), or evidencing other conditions not normally covered under the original New Vehicle/SAV Limited Warranty or applicable emissions warranty. Modifications excluded from warranty coverage include any aftermarket parts that affect the turbocharger system, or if there are other conditions that would normally exclude it from warranty coverage." |
| 131410 | 2018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. Voluntary Emissions Recall Campaign 10E-A02: N54 Inspection and Replacement of Injectors. The piezo injectors may cause misfire faults with erratic engine operation. |
| 121412 | 2018-12-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM. N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken. |
| 120412 | 2018-12-03. Service bulletin. ENGINE. N55: Idle Fluctuates Briefly After a Cold Engine Start. Under certain engine cold starts, the engine idle may fluctuate during the first 10-20 seconds of operation before becoming stable. No faults will be stored in this situation, which will usually only occur at specific engine temperatures, making it difficult to reproduce in the workshop. Unfavorable DME software calibration |
| B111117 | 2018-12-03. Service bulletin. ENGINE. ?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye. |
| B110815 | 2018-12-03. Service bulletin. ENGINE. N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. * B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair * B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints * B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity * B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. * Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption * Spark plugs fouled with engine oil and excessive engine oil consumption * Excessive engine oil consumption All Vehicles: On vehicles, where an excessive oil consumption between services is the only complaint, a complete oil consumption test as described in SI B11 03 13, must be performed first before replacing the valve seals. On vehicles exhibiting reproducible smoking from the tailpipe when hot, additional engine diagnostic steps (e.g. engine compression test, leak-down tests; inspection of the crankcase ventilation lines and turbo intake/outlet tubes for excessive oil accumulation) should be performed and documented prior to replacement of the valve seals, in order to eliminate other possible causes. Refer to the SIBs listed above for important diagnostic tips. Do not remove the intake manifolds to clean the intake valve carbon. |
| 240313 | 2018-11-26. Service bulletin. ENGINE; POWER TRAIN. N52T/N55 with 8HP45: Delay in Engine Response. When slowing down to lower suburban road speeds and then accelerating, a delay in engine response may be experienced. This situation may be more noticeable when driving in a bend in the road or on roads with a rising gradient. Unfavorable EGS and DME software calibration |
| 130712 | 2018-11-26. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation. |
| 130409 | 2018-11-26. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. "N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)." |
| B110113 | 2018-11-26. Service bulletin. ENGINE. N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently. |
| 121412 | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. ?SI B12 14 12 April 2013 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 14 12 dated January 2013. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken. |
| 121412 | 2018-11-26. Service bulletin. ENGINE. N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken. |
| 120911 | 2018-11-26. Service bulletin. ENGINE; ELECTRICAL SYSTEM. N55 - Delayed Throttle Response When Driving Off. Delayed throttle response when driving off with a high engine load This problem occurs mainly under the following conditions: * High ambient outside temperatures * The air conditioning is switched on * The steering wheel is turned slightly DME software calibration |
| 121412 | 2018-11-26. Service bulletin. ENGINE. SI B12 14 12 October 2014 Engine Electrical Systems Technical Service This Service Information bulletin supersedes SI B12 14 12 dated February 2014. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine loses power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored: E70, E71, E82, E88, E90, E91, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies may have faulty assembly bolts. One or more of the four assembly bolts have loosened or broke |
| 120212 | 2018-11-26. Service bulletin. ENGINE. INFORMATION This section only applies to vehicles that require cleaning the intake valve and intake ports. Refer to the applicable Service Information bulletin or ETK if carbon cleaning was not the root cause for the complaint. Reuse the strut brace bolts. Part Number Carbon Blaster Walnut Shells: Replacement media, 20/30 SAE or 0.45-0.80 mm walnut shells can be sourced locally or through one of the following distributors: MARCO(r) Corporate - (800) 252-7848, ext. 284 - marcousa.com/index.cfm Trinity Tool Company - (800) 587-4626 - www.trinco.com McMASTER-CARR(r) - www.mcmaster.com Refer to EPC for applicable gaskets and bolts. |
| 620613 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster. |
| 240313 | 2018-11-13. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM:SOFTWARE. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software |
| 130712 | 2018-11-13. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation. |
| 121712 | 2018-11-13. Service bulletin. ENGINE; POWER TRAIN. N52T / N55 with 8HP45: Delay in Engine Response. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.