WenmarOpen by Wenmar Pro

Service bulletins for the 2019 BMW 430i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

63 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
B0102242026-08-03. Warranty extension. ENGINE. The EVAP systems purge (vent) valve limited warranty for defects in materials and / or workmanship has been extended to 15 years / 150,000 miles as determined from the original first in-service / delivery date.
B0102242026-05-18. Warranty extension. ENGINE. The EVAP systems purge (vent) valve limited warranty for defects in materials or workmanship has been extended to 15 years / 150,000 miles as determined from the original in-service date.
B0102242024-05-31. Warranty extension. ENGINE. EVAP SYSTEM PURGE (VENT) VALVE EXT LTD WTY (ELW) 15/150
B0114232023-12-06. Service bulletin. ENGINE AND ENGINE COOLING. PRESSURE CONTROL VALVE (PCV) EXTENDED LTD WTY 15 YEARS/150,000 MILES
B1701212022-06-21. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine.
B1701212022-05-31. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine.
B1101202021-08-09. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN. On rare occasions during an engine oil service, the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing.
B1103212021-07-19. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. B58 ENGINE: ENGINE OIL FILTER REMOVAL PROCEDURE AND TOOLS . A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.
B1213182021-03-15. Service bulletin. ENGINE AND ENGINE COOLING. COMBUSTION CONTROL VALVE LIFT AT IDLE: The vehicle will run rough or hesitate when accelerating from a stationary position.
B1304202020-06-15. Service bulletin. ENGINE AND ENGINE COOLING. TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation I01 only: FC 124103 - Mixture control: mixture too lean FC 124101 - Mixture control: Mixture lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.
B1101202020-06-15. Service bulletin. ENGINE. B58C AND B58M ENGINES ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing.
B6105202020-04-20. Service bulletin. ENGINE. CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
B1213182020-04-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. DME FC 21A02D - COMBUSTION CONTROL: VALVE LIFT AT IDLE This Service Information Bulletin (Revision 3) replaces SI B12 13 18 dated September 2019. The vehicle will run rough or hesitate when accelerating from a stationary position.
B1233142020-03-16. Service bulletin. ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME: This Service Information Bulletin (Revision 5) replaces SI B12 33 14 dated February 2016. The Service Engine Soon light is on. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1101202020-03-16. Service bulletin. ENGINE AND ENGINE COOLING. ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: This Service Information Bulletin (Revision 1) replaces SI B11 01 20 dated February 2020. On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing (1).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.