WenmarOpen by Wenmar Pro

Service bulletins for the 2018 BMW 430i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

193 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B5207182019-02-25. Service bulletin. SEATS. SEAT THIGH SUPPORT UPHOLSTERY IS PROTRUDING. The upholstery may dislodge slightly from the thigh support base over time from repeated compression due to normal use.
B1107172019-02-25. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. FAULT 118002 - MIXTURE TOO RICH SETS DURING WINTER WITH COLD AMBIENT TEMPERATURES. The Service Engine Soon (MIL) light is on with the following fault stored in the Digital Motor Electronics (DME). Fault: 118002 - Mixture too rich In the situation being described.
B6211182019-02-25. Service bulletin. ELECTRICAL SYSTEM. BLACK SPOT IN THE CENTRAL INFORMATION. This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: â?¢ Warranty section - Programming information added. A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.
B5208182019-02-25. Service bulletin. SEATS. FRONT PASSENGER SEAT SPORADIC MOVEMENT. Occasional stopping of seat adjustability movement in the driver and front passenger seats when occupied.
B5125182019-01-07. Service bulletin. STRUCTURE. RATTLE NOISE FROM LOWER A-PILLAR. A rattle noise is present from the lower area of the A-Pillar. Due to a manufacturing error, the bolt securing the front door brake/stop to the A-Pillar may have loosened over time.
B6211162018-12-10. Service bulletin. ELECTRICAL SYSTEM. Center Information Display Switching off. INFORMATION The brightness of the CID will reduce and may switch off completely due to high temperature rise inside the vehicle. This situation is to protect the function of the CID. After lowering the temperature, the normal functions are restored. The increased temperature, protective switch-off is the reason for the fault. The fault code does not indicate a defective head unit. The normal maximum temperature operation for the head unit is between 167 and 194 F. Within these values, the CID will gradually diminish in brightness until it completely switches off. Replacing parts or programing the vehicle will not rectify the situation. The root cause is the very high temperature and is not a fault of the vehicle's systems.
B6210162018-12-10. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL. HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
B6103152018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE; STEERING; STRUCTURE; EQUIPMENT; WHEELS; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE; LANE DEPARTURE. Various Check Control Messages Caused by Shorted K-CAN This Service Information bulletin supersedes SI B61 03 15 dated April 2016. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior:Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pill
B3104162018-12-10. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM:SOFTWARE. Thumping noises from the front section of the vehicle. Thumping noises from the front section of the vehicle may occur when driving over poor road surfaces. Software of the Variable Damper Control (VDC)
B2601162018-12-10. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT; POWER TRAIN. Vibration or Knocking Noise from the Center of the Vehicle. When accelerating, there is a knocking, or vibration, felt from the center of the vehicle. This sensation can be easily duplicated when accelerating with the transmission in 2nd or 3rd gear (manual mode). Torque flex in the rear driveshaft.
B8403142018-12-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT. Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
B6609162018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
B5123152018-12-10. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH; STRUCTURE:BODY:DOOR. SI B51 23 15 Body Equipment May 2016 Technical Service The Driver's Side Front/Rear Door Can No Longer Be Opened from the Outside This Service Information bulletin supersedes SI B51 23 15 dated September 2015.. A driver's-side door cannot be opened by the outside door handle. This concern can also affect the driver's side rear door on the F34 and F36. The Bowden cable has become detached.
B5112162018-12-10. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; VISIBILITY:REARVIEW MIRRORS/DEVICES; VISIBILITY. Passenger Side Mirror Dimming Feature Operational Change. INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.
B6206162018-12-10. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster Resets during Active Navigation. The instrument cluster (MID KOMBI) fails sporadically (all gauges falling briefly to zero, flashing of all indicator lights) and resets. Reset occurs during active route guidance and predictably when passing certain geographical positions. Software error in navigation head unit
B6123152018-12-10. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. "The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. The low washer fluid warning light is illuminated even though the washer fluid tank is full. There are no faults stored in the system for the washer fluid level switch. CAUSE A non-approved washer fluid is used (fluids that contain a silicone additive, normally colored other than blue). INFORMATION The washer fluid level sensor is a contactless capacitive sensor. The sensor sends a low fluid level signal to the gateway module (FEM - Front Electronics Module or BDC - Body Domain Controller) which in turn displays a low washer fluid warning in the instrument cluster. The use of a ""non-approved"" washer fluid (silicone-based fluid) can cause the low fluid warning light to come on even when the reservoir is full. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates."
B6103152018-12-10. Service bulletin. STEERING. Various Check Control Messages Caused by Shorted K-CAN. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior: Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pillar trim
B1209162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic
B1116152018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.
B8403142018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
B6502162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B6409152018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Service Information bulletin supersedes SI B64 09 15 dated January 2016. designates changes to this revision SUBJECT Whistling Noise Coming from the Center Vent - A/C is Off. A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
B6103142018-12-10. Service bulletin. ELECTRICAL SYSTEM. February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
B1303152018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE; EQUIPMENT. SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B1233142018-12-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; POWER TRAIN. This Service Information bulletin supersedes SI 12 33 14 dated December 2015. SUBJECT Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.