WenmarOpen by Wenmar Pro

Service bulletins for the 2012 BMW 335i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

592 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
6308142018-11-13. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Active Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. CAUSE Broken mounting bolt holding on the rear height sensor bracket
B6519152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. XM Satellite Radio Reception. INFORMATION Currently Satellite Radio is provided by SiriusXM for BMW customers. SiriusXM is the only company currently broadcasting Satellite Radio in North America. Satellite radio is broadcast from two different sets of Satellites using different earth orbits. XM uses geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. This is different than Sirius Satellites in a Highly Elliptical Orbit (HEO) which currently come in to the vehicle at a higher angle to the horizon. As of April 2016 Sirius equipped head units will move to the XM Satellites constellation and will show the same location based cutouts. SiriusXM is currently updating the repeater network to cover areas of low reception, but the general disadvantage of geostationary satellites can't be compensated completely. Buildings, hills, trees, highway sound blocking walls or any other obstacles might block the satellite signal coming from the south at a 32 degree elevation angle and might cause audio cut outs in absence of terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets flatter. Adverse weather conditions will affect reception. Sirius XM will increase the amount of Sirius and XM repeaters gradually to improve situation in metropolitan areas. When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Do not compare an XM equipped vehicle to a Sirius equipped vehicle. Replace no parts Customers should direct all reception complaints to one of the following: BMW Customer Relations department at either 1-800-831-1117 or customerrelations@bmwusa.com BMW Genius Hotline 1-844-443-6487 or to the dealers onsite BMW Genius Customers must provide the exact location (street address or Latitude/Longitude), weathe
B6212152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
B6211152018-11-13. Service bulletin. ELECTRICAL SYSTEM. Head-Up Display (HUD) Rattling Noises During Image Adjustment or While Driving. When operating the Head-Up Display (HUD) adjustment a noise can be heard from inside the dashboard behind the Instrument Cluster. While driving over rough roads something can be heard rattling inside the HUD. Internal HUD failure.
B6123152018-11-13. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. "The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations. We recommend using ""BMW Group approved"" washer fluid when servicing the vehicle or performing repairs on the windshield washer system. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates. If the correct washer fluid is being used, diagnose the system using normal troubleshooting with ISTA. A fault code may be stored if an electrical fault occurs in the circuit. PARTS INFORMATION Part NumberDescriptionQuantity83 19 2 406 220BMW WWS Cold Weather Concentrate 35% 55 GalAs needed83 19 2 361 205BMW Windshield Washer Concentrate 1 GalAs neededNote: As applicable, do not exceed your state's maximum for the allowable amount/percentage of ""Washer Concentrate"" that can be used when mixing the windshield washer fluid solution. WARRANTY INFORMATION The issue described in this bulletin is not a vehicle-related defect in materials or workmanship. If a vehicle repair is required as a result of this issue, it is are not claimable under a BMW limited warranty."
B3408142018-11-13. Service bulletin. SERVICE BRAKES, HYDRAULIC. ?SI B34 08 14 Brakes December 2015 Technical Service This Service Information bulletin supersedes SI 34 08 14 dated July 2015. designates changes to this revision SUBJECT Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
B1233142018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B1126152018-11-13. Service bulletin. POWER TRAIN; ENGINE. Delivery Stop: B58 Engine - Check Crankshaft Bearing Shells.A Delivery Stop has been issued on F30 and F32 certain vehicles produced from July 2015 (start of production) to December 2, 2015. These vehicles may have upper guide bearing shells that may exhibit wear at low mileage. There are 45 vehicles affected by this stop. For your convenience, attached you will find the list of affected VINs. This bulletin will be updated with repair instructions and warranty information when it becomes available. Affected vehicles can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA Light with a specific description.
B0906152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL. New programming feature: Exclusion of Infotainment Control Units from Programming. Programming with ISTA/P 3.57.4, or a more recent update, displays a new Pop-Up window providing options for systems programming.
B0117152018-11-13. Service bulletin. EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. "N54T Engine Fuel Injectors - Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the fuel injectors to: 10 years/120,000 miles as determined by the vehicle's original in-service date This ""component-specific"" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release during the first quarter of 2016."
B6526062018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. "The Disclaimer screen automatically disappears from the CID after 10 seconds. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/28...12/2/2015 Page 2 of 2 An enhancement was made to the Car Communication Computer (CCC) and MASK (Multi Audio System Controller) in 2006 so the customer does not have to manually accept the ""Disclaimer"" screen each time. Older vehicles prior to the production dates listed above that are programmed with ISTA/P 2.52 or higher will also get this enhancement. WARRANTY INFORMATION Not applicable."
B6509152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6406132018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
B6203122018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. """Efficient Dynamics"" in the Instrument Cluster Partially Displayed During CC Message. After switching from terminal 15 to terminal R, the ""Efficient Dynamics"" wording in the instrument cluster, below the tachometer, is partially displayed while a CCM (Check Control Message) is shown. Only the word ""Efficient"" is displayed. Software error in the instrument cluster multi-information display"
B1240152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. "Due to a DME software status error, the on-board diagnostics (OBD) for the catalytic convertor and downstream oxygen sensor may not function properly. This could result that the OBD readiness for ""Oxygen sensor"" will not set as completed, but it would not have any effect on the actual tailpipe emissions."
B6517152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL; EQUIPMENT. "Active Sound Design ASD inoperative after programming. After programming with ISTA/P V3.56.1 Active Sound Design (ASD) no longer provides simulated engine sounds A fault is stored in the ASD module. Fault Code 8053A5 ""ASD; invalid coding data for equalizing"" Invalid ASD coding data"
B6516152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. Navigation CIC vehicle positioning temporarily incorrect. The Navigation system may temporarily display the vehicle in the wrong location. This mainly occurs on short sections of road and the vehicle position may take 2 or more minutes to be shown correctly. Invalid calculation in the CIC head unit.
B3302152018-11-13. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. "Grinding or cracking noise when putting vehicle in gear/ ""Drive Disturbed"" displayed. A metallic grinding or cracking noise is heard from the rear of the vehicle when selecting Drive or Reverse. There may also be a Check Control message ""Drive Disturbed"" displayed. CAUSE The inner and/or outer universal joint on the right and/or left rear output shaft has failed."
B1114152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
B0703142018-11-13. Service bulletin. EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6502152018-11-13. Service bulletin. EQUIPMENT. iDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
B6126142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. "Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: ? ""8044A3 - Wiring, horn short circuit to earth"" ? ""8044A4 - Wiring, horn short circuit to positive"" ? ""8044A5 - Wiring, horn relay is defective or short circuit to positive"" Water has entered the horn and caused it to fail internally (shorted out)."
B2402152018-11-13. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 8HP: Transmission Fluid Loss from Cooler Lines Connections. There is a transmission fluid leak in the area around the oil cooler lines (on the transmission side). CAUSE Damaged o-rings due to unfavorable cooling line connection tolerances
B1305122018-11-13. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. N20 Engine: Ticking Noise from High-pressure Fuel Pump. The customer complains of a high-frequency ticking noise from the engine compartment. The noise can be heard inside and outside the vehicle. Mechanical vibrations inside the high-pressure fuel pump
1215132018-11-13. Service bulletin. ENGINE. ?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.