WenmarOpen by Wenmar Pro

Service bulletins for the 2012 BMW 335i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

592 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
1304092018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (?wet?) with fuel, while the injector tips are covered with a layer of carbon deposit.
1216112018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
0102122018-12-03. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. "BMW NA has agreed to extend the emissions warranties of the turbocharger's wastegate to: ??8 years or 82,000 miles, whichever occurs first, as determined from the vehicle's original in-service date select the ""Vehicle Comment"" button to display the extended coverage information. The terms of the original New Vehicle/SAV Limited Warranty and applicable emissions warranty still apply. BMW NA will not provide warranty coverage to any Settlement Class Member's vehicle containing modifications or alterations to the turbocharger or its wastegates (software, hardware or otherwise), or evidencing other conditions not normally covered under the original New Vehicle/SAV Limited Warranty or applicable emissions warranty. Modifications excluded from warranty coverage include any aftermarket parts that affect the turbocharger system, or if there are other conditions that would normally exclude it from warranty coverage."
1314102018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. Voluntary Emissions Recall Campaign 10E-A02: N54 Inspection and Replacement of Injectors. The piezo injectors may cause misfire faults with erratic engine operation.
1215132018-12-03. Service bulletin. ENGINE. N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp is illuminated; Engine Malfunction warning is illuminated; and the vehicle has reduced power output. Various faults related to VANOS operation are stored in the DME. While performing the test plan, the results may appear to be inconclusive because the fault will not clear from DME Fault Memory. The ISTA/D diagnostic test plan does incorporate a VANOS bleed function, but it does not advise the technician to bleed the VANOS system after a VANOS or engine oil supply component replacement. CAUSE This is due to an error in the current level of ISTA/D. The error will be corrected with ISTA/D 2.41.0.
1304092018-11-26. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. "N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."
B1209182018-11-26. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. NOISE FROM ENGINE WHEN STARTING. Noise when starting the engine. Engine making a rattling/grinding noise near the 12 volt starter motor. The following fault has been stored in the DME fault memory: * 21A511 - Start system, pinion starter motor: Timeout The following faults are also possible: * 21A504 - EGS, separation clutch: jammed open * 21A50A - Start system, pinion starter: Timeout successively occurred multiple times * 21A510 - Start system, EME: Timeout Consequential damage to flywheel (Torsional vibration damper) and automatic transmission may have also occurred. The starter motor is broken. It may be indicated by:
1112122018-11-26. Service bulletin. ENGINE. N20 Engine: Engine Oil Filter Application. INFORMATION The current version of EPC does not provide all available options for the engine oil filters that are used in the N20 engine. The illustrations below will help identify the proper engine oil filter application until the EPC is corrected. Vehicles produced prior to 6/2012 will be equipped with a black plastic oil filter housing (1). In this case, engine oil filter kit P/N 11 42 7 634 291 should be used. Vehicles produced as of 6/2012 and later will be equipped with a silver aluminum oil filter housing (1). In this case, engine oil filter kit P/N 11 42 7 640 862 should be used.
1305142018-11-26. Service bulletin. ENGINE. . INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
1301142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software
1224122018-11-26. Service bulletin. ENGINE. N20 and N26 Engine: DME FC CDA904 FA CAN Message State Trailer 0x2E4 Is Missing.
1222122018-11-26. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE; POWER TRAIN. Service Action: Program Control Units. When coming to a stop, there is the possibility of an unfavorable judder. This is due to the software parameters for downshifting and transmission clutch control. CAUSE Unfavorable vehicle software
1110122018-11-26. Service bulletin. ENGINE. ?N20 Engine: Repeated Juddering or Surging While Accelerating. The vehicle judders or surges repeatedly while accelerating in hot ambient temperatures between 3,000 RPM and 5,000 RPM. The Service Engine Soon lamp is not illuminated, and no fault codes are stored in the vehicle memory related to this complaint. CAUSE The EPDW (electropneumatic pressure convertor) for the turbocharger wastegate valve is binding internally.
1214122018-11-26. Service bulletin. ENGINE. SI B12 14 12 October 2014 Engine Electrical Systems Technical Service This Service Information bulletin supersedes SI B12 14 12 dated February 2014. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine loses power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored: E70, E71, E82, E88, E90, E91, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies may have faulty assembly bolts. One or more of the four assembly bolts have loosened or broke
1202122018-11-26. Service bulletin. ENGINE. INFORMATION This section only applies to vehicles that require cleaning the intake valve and intake ports. Refer to the applicable Service Information bulletin or ETK if carbon cleaning was not the root cause for the complaint. Reuse the strut brace bolts. Part Number Carbon Blaster Walnut Shells: Replacement media, 20/30 SAE or 0.45-0.80 mm walnut shells can be sourced locally or through one of the following distributors: MARCO(r) Corporate - (800) 252-7848, ext. 284 - marcousa.com/index.cfm Trinity Tool Company - (800) 587-4626 - www.trinco.com McMASTER-CARR(r) - www.mcmaster.com Refer to EPC for applicable gaskets and bolts.
1114142018-11-26. Service bulletin. ENGINE. Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
7102142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; EQUIPMENT:OTHER:LABELS. Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
6206132018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
1301142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL. "N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: * 26F500 - SCR system, efficiency: Efficiency too low * 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of ""Incorrect diesel exhaust fluid"" may be displayed with ""no start scenario countdown"" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. * 2CE400 - SCR system: System error and poor urea/water mixture quality detected * 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high * 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 * 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software"
1233142018-11-13. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
1801142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. Exhaust Leak on Diesel Particulate Filters. An exhaust leak develops on the Diesel Particulate Filter (DPF) around the area of the flexible coupling. Age or wear on the flexible coupling
5106142018-11-13. Service bulletin. ENGINE. Service Action: Repair Corrosion Protection Engine Compartment. Various engine compartment battery cable mounting points are not sufficiently protected against corrosion. Lack of corrosion protection can lead to improper connections associated with the battery cables. AFFECTED VEHICLES This Service Action involves F30 3 Series vehicles produced from June 2012 to January 2013. First check if a Service Action label with a code number 670 is already attached to the B-pillar. If a code number 670 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
0104142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
6407132018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING. Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
1225132018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Reduced Engine and Air-Conditioning Performance. When driving with high outside ambient temperatures, repeated stop and go, or high load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances the compressor is switched off. There could be any of the following faults stored depending on the conditions present at the time. DME * Fault 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault EGS (also possibly set) * Fault 421722: DME/DDE interface: Forced upshift due to thermal engine protection request IHKA (possibly set without DME or EGS faults) * Fault 801224: Air conditioning compressor: Shut-down due to excess pressure in refrigerant circuit * Fault 801228: Blower output stage: Blower output reduction due to power management The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 850W electric fan over-boost or high speed function. 2. The electric cooling fan design was not robust enough for continuous over-boost or high speed operation.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.