WenmarOpen by Wenmar Pro

Service bulletins for the 2011 BMW 328i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

145 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
B6203152018-12-17. Service bulletin. ELECTRICAL SYSTEM. Door Open Message Displayed, Even Though Door Is Closed. The customer complains that while driving, a CCM (check control message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. Unspecified FRM door lock status due to voltage variations
B8403142018-12-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT. Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
B1106162018-12-10. Service bulletin. EQUIPMENT; ENGINE. N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
B1211162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. ISTA/P Cannot Program an E-Series N55 Replacement DME. ISTA/P fails when attempting to program a replacement DME (MEVD172) on BN2000 E-Series vehicles with the Continental HPP. Part number: 12 14 8 618 483. DME logistic error between the replacement hardware and basic software prevents correct programming with ISTA/P.
B1106162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING. N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
B1221102018-12-10. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
B8403142018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
B6502162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B1303152018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE; EQUIPMENT. SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B0703142018-12-10. Service bulletin. ENGINE; STEERING; ELECTRICAL SYSTEM; EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6507092018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
B5409072018-12-10. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM; EQUIPMENT. ?RETRACTABLE HARDTOP STATUS REQUEST SUPPLEMENT. INFORMATION Documents have been developed showing the known correct statuses for all hall sensors and micro switches used to operate the retractable hard top (RHT). This document is intended to act as a supplement to the diagnostic information available in ISTA. Comparing these statuses to the actual statuses of a vehicle with a functional problem may assist in narrowing down which sensor/switch is contributing to the functional problem. For E93, the status request may be found by connecting the car to ISTA and selecting: Control module functions/CTM Convertible top module/Diagnosis Requests ?Sensors/Switches For F33/F83, the statuses should be checked using the applicable test plan as instructed in attachment B54 09 07 F33 F83 RHT Status.pdf. For I15, the statuses should be checked using the applicable test plan as instructed in attachment B54 09 07 I15 Top Status.pd
6522122018-12-03. Service bulletin. EQUIPMENT. Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
6501102018-12-03. Service bulletin. EQUIPMENT. "CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
6106062018-12-03. Service bulletin. ELECTRICAL SYSTEM. Junction Box Pin Assignment Change. When replacing the Junction Box (fuse box) using P/N 61 14 6 978 270 or later, note that various pin assignments have changed. The following additional work procedure is necessary to properly perform this repair.
1221122018-12-03. Service bulletin. VEHICLE SPEED CONTROL. "N51, N52K and N52T: Idle Fluctuation During Engine Warm-up Phase. After a cold engine start, the idle speed may be unstable or start fluctuating up and down slightly while the vehicle is stopped. On vehicles with automatic transmissions, roughness or shuddering may be felt during this warm-up period when diving away slowly in ""D"" or in ""R"" without depressing the accelerator pedal. No relevant errors are stored in the DME fault code memory, and these symptoms are no longer present once the engine is at operating temperature (> 90C). Unfavorable DME software"
6515122018-12-03. Service bulletin. EQUIPMENT. "Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
6113052018-12-03. Service bulletin. ELECTRICAL SYSTEM. "Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
5139112018-12-03. Service bulletin. EQUIPMENT. Intermittently the trunk lid does not pop open when using the remote, or latch when closing. If the vehicle is driven and the trunk is not closed fully, a Check Control message will be displayed in the instrument cluster. CAUSE The trunk lid is out of tolerance. When opening or closing the trunk lid, the latch rubs against the striker because of insufficient clearance.
5115082018-12-03. Service bulletin. VISIBILITY:GLASS, SIDE/REAR. ?SI B51 15 08 Body Equipment October 2012 Technical Service. This Service Information bulletin supersedes SI B51 15 08 dated July 2008. designates changes to this revision SUBJECT Rear Window False Anti-trap Activation. INFORMATION The anti-trap protection feature may be activated when no obstruction is present. This may occur at either one or both of the rear windows. The root cause of the false anti-trap activation may be difficult to determine. The attached diagnosis flowchart has been developed to assist with determining the actual root cause of the failure as well as to help prevent unnecessary part replacements. The root cause is typically either an issue with the window system, or an electrical/software issue. The diagnosis flowchart will help ensure that repairs are only carried out for the system that is most likely at fault. Refer to B511508_Attachment. PARTS INFORMATION Refer to the Electronic Parts Catalog (EPC) for the appropriate parts noted in the diagnostic flowchart. WARRANTY INFORMATION Not applicable.
6511122018-12-03. Service bulletin. EQUIPMENT. Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
6510132018-12-03. Service bulletin. SEATS. "The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding."
5136082018-12-03. Service bulletin. VISIBILITY. "Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
3407132018-12-03. Service bulletin. SERVICE BRAKES. Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production instead of the appropriate 24-month interval.
1214122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.