WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Bentley Continental

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

708 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
2061171/72022-07-09. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. New Continental GT/GTC and New Flying Spur - V8 Kovomo - Fuel Pressure Regulation - Numerous DTCs. Customer statement / workshop findings Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: - P310B00 Low Fuel Pressure Regulation with symptom code 2636 - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - P018B00 - Fuel Pressure Sensor B Circuit Range/Performance with symptom code 17871 - Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues Technical background In the event the customer complaint relates to the following: - Customer experienced poor start up - proceed with the remaining instructions NOTE: The operative must gather information regarding the Customer experience regarding when the issue occurred for example: Pre- conditions, warning lights and driveability at time issue occurred, details when the vehicle was last refuelled and the grade of fuel used The operative must now use the information contained within the Measure section to determine the correct analysis and repair procedure
2066480/12022-07-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Headlamp switch not working/not illuminated - Numerous DTCs within 0009-Central Electrics (BCM1). Customer statement / workshop findings Customer statement: - Headlamp switch not working/not illuminated when the ignition is switched on (following an ignition switch off) And/or - Yellow warning light/message within DIP (Adaptive lighting fault) And/or - Loss of rear fog light activation And/or - Loss of all-weather lighting mode activation And/or - Headlamps will default to dipped beam (however, high beam activation will still be possible manually) Workshop findings: The following DTCs may also be evident within 0009 - Central Electrics control module U110B00 - Light switch no communication And/or B126A29 - Light switch signal not reliable And/or U1122300 - Fault value received by data bus Technical background - The condition will not occur when the ignition is on or whilst the vehicle is being driven - The condition only occurs as the headlamp switch goes into a Sleep state after the ignition is switched off - The condition is evident to the driver when the ignition is next switched on In the event the afore mentioned symptoms are evident please carry out the instructions within the Measure section
2063855/42022-07-06. Service bulletin. LANE DEPARTURE; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE. DTC B17B801 and/or B17B804 - evident within address 0019 and/or DTC U112300 evident in 00A5. Customer statement: Lane Assist and/or Traffic Assist are not functional Workshop findings: DTC - B17B801 - Steering Wheel Touch Recognition Control Module evident within address 0019 And/or DTC B17B804 - Steering Wheel Touch Recognition Control Module electrical error - evident within address 0019 And/or DTC U112300 with symptom Code 1123220 within address 00A5 Technical background: Revision history TPI 2063855/4 - Additional request to replace the control module (as Figure 1) in conjunction with the steering wheel
2058423/82022-07-06. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. New Continental GT/GTC, New Flying Spur and Bentayga - Low Oil Pressure Warning During Early Vehicle Life. Customer statement / workshop findings: Warning on the Driver Instrument Panel (DIP) - Oil pressure too low DTCs relating to oil pressure may also be stored within the Master ECU. Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU). Measure: VERY IMPORTANT: Prior to conducting the onward instructions, the following symptoms MUST be evident - Warning on Driver Instrument Panel (DIP) Oil pressure too low And/or - Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU) Should any of the afore mentioned not be evident and the symptoms cannot be reproduced No further action should be taken unless the issue can be reproduced or demonstrated by the customer In the event the symptom/s are evident please conduct the onward Diagnosis Instructions
2055036/52022-06-02. Service bulletin. ELECTRICAL SYSTEM. My Bentley - Connected services. Customer statement / workshop findings: Complaints relating to My Bentley connected services. Technical background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query. My Bentley support have access to additional admin tools and systems to help resolve any queries; and also have the ability to raise DISS technical queries if required.
2066724/12022-05-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. FPIN tag - Not attached Technical background: Please Note: This is an ongoing exercise and therefore the latest VIN list can be found within the Bentley Hub The white FPIN tag is not attached to the vehicle keys to the vehicle keys (SC22/13) In the event the white FPIN tag is evident as shown in 2 and 3, the 10 digit FPIN vehicle code can be entered into MMI, in this scenario there is no need to raise a DISS query for a new FPIN, the operative should refer to the Identification section of this TPI to ensure the specific VIN is removed from the applicability list.
2066669/12022-05-07. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Engine coolant - Overheat condition - Warning evident within the DIP - DTC's P2B6500 and P2B8600 are evident. Customer statement / workshop findings: - Engine cooling system overheating And/or - Coolant loss And/or - Warning light in Drivers Information Panel (DIP) The following DTCs may also be evident within 0001 and/or 0011 - P2B6500 and/or P2B8600.
2064582/32022-05-07. Service bulletin. ELECTRICAL SYSTEM; SUSPENSION. Vehicle sitting low on one or more corners when static with no relevant DTCs stored. Customer statement / workshop findings: - Vehicle sitting low on one or more corners when static - No relevant DTC’s are evident Technical background: Refer to the Measure section of this TPI
2066852/12022-05-07. Service bulletin. ELECTRICAL SYSTEM. Shaker speaker - Diagnostic checks. Customer statement / workshop findings: Customer complains of poor quality music output from the shaker speaker due to a rattling noise/sound distortion. Technical background: There have been instances where shaker speakers have been changed under warranty for the complaint of sound distortion, yet when tested by Bentley motors and the supplier, no fault could be found with the returned unit. Measure: To ascertain the difference between distortion or a rattle emanating from a loose/surrounding component Or The shaker speaker itself is incorrectly secured and/or at fault please conduct the following steps before replacing any components
2062035/62022-05-07. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. New Continental GT and GTC - Repeat window drop glass concerns. Customer statement: - Incorrect operation of the front and rear drop door glass functionality - Front and/or rear drop door glass fails to open/close or attempts to close and reopens once contact has been made between the glass and applicable seal Workshop findings: - DTCs for window regulator motor no basic setting B148754 evident within any of the 4 window control modules (diagnostic address 42, 52, BB and BC) for loss of basic settings Technical background: A customer complaint of windows failing to open/close correctly Including The loss of Basic Settings DTC must be evident before proceeding
2066287/32022-04-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. FPIN tag - Not attached to the vehicle keys (SC22/05). Technical background: Please Note: This is an ongoing exercise and therefore the latest VIN list can be found within the Bentley Hub. The white FPIN tag not attached to the vehicle keys. Remedy: Refer to the instructions within the Work section to completion.
2066287/22022-04-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. FPIN tag - Not attached to the vehicle keys (SC22/05). Technical background: The white FPIN tag not attached to the vehicle keys. Remedy: Refer to the instructions within the Work section to completion
2066287/12022-04-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. FPIN tag - Not attached to the vehicle keys (SC22/05). Technical background: The white FPIN tag not attached to the vehicle keys. Remedy: Refer to the instructions within the Work section to completion
2063678/32022-04-08. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. P245000 - EVAP System Switching Valve "A" Performance/Stuck Open DTC logged - V8 Kovomo. Customer statement / workshop findings: Emission control system warning light illuminated within the DIP (Figure 1). Workshop findings: DTC P245000 - EVAP System Switching Valve "A" Performance/Stuck Open - With symptom code 11952 Technical background: Refer to the Measure section of this TPI
2065698/12022-04-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ELECTRICAL SYSTEM. V8 Kovomo - Emission control warning illuminated within the DIP - Exhaust Gas Temperature Sensor DTC's evident. Customer statement: Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) Workshop findings: U061F00: Lost Communication With Exhaust Gas Temperature Sensor Bank 1 Sensor 1 U062100: Lost Communication With Exhaust Gas Temperature Sensor Bank 2 Sensor 1 After further investigation the wiring harness leading to the Exhaust gas temperature sensor (Bank 1 and/or Bank 2) runs close to the sub-frame may rub/contact the edge of the bracket inside of the wheel arch cover/liner See the examples shown in Figure 1 (Chaffed/damaged wiring Bank 1) And Figure 2 (Broken/damaged wiring Bank 2) Technical background: Technical product information V8 Kovomo - Emission control warning illuminated within the DIP - Exhaust Gas Temperature Sensor DTC's evident Transaction No.: 2065698/1
2066511/12022-04-08. Service bulletin. STEERING:STEERING CONTROL MODULE; STEERING; ELECTRICAL SYSTEM. Warnings within the DIP for the rear steering system - DTC P060700 evident within diagnostic address 00CB. Customer statement / workshop findings: - Warnings within the DIP for the rear steering system (Figure 1) Workshop findings: - DTC P060700 evident within diagnostic address 00CB - Rear Axle Steering control module Technical background: In the event the issue is as described the operative should conduct the instructions within the Measure section of this TPI
2064338/22022-04-08. Service bulletin. ELECTRICAL SYSTEM:WIRING; SUSPENSION; ELECTRICAL SYSTEM. Warning light illuminated within the DIP - DTC C103711 - Evident within Address 74. Customer statement / workshop findings: Air suspension warning light within the DIP Workshop findings: The DTC shown below is evident within address 74 - C103711 - Right rear level control system sensor Short circuit to Ground - C103316 - Right sensor voltage supply for vehicle levelling Voltage too low Technical background: Previous instances have highlighted the following after inspection: - Broken wires - Kinked wiring - Loose Rear Right Height sensor G77connection - Defective Rear Right Height sensor G77
2066393/12022-04-08. Service bulletin. ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SENSORS; ELECTRICAL SYSTEM. PDC system not working or PDC system false detection. Customer statement / workshop findings: - PDC system not working or PDC system false detection - Warning evident within the DIP (Figure 1). Workshop findings: Parking aid sensor Range/Performance DTCs evident within numerous control units Technical background: Refer to the Measure section of this TPI.
2052349/82022-04-08. Service bulletin. AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE; ELECTRICAL SYSTEM; SEAT BELTS. Front seatbelt - Diagnostic Trouble Codes - B130474 and/or B130574. Customer statement / workshop findingsL Diagnostic Trouble Codes (DTCs) evident in Address: 0015 System name: 15 - Airbag Control Module B130474: Left front seat belt tensioner control module Actuator deviated B130574: Right front seat belt tensioner control module Actuator deviated The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings. Technical background: Dummy seat belt buckles of any description MUST NOT be used under any circumstances, Figure 1 shows an example of a dummy seat belt buckle
2062184/52022-04-08. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE:ELECTRICAL; PARKING BRAKE. Electronic Parking Brake (EPB) functionality issues. Customer statement / workshop findings: The following issues could be evident during PDI or found whilst in service - Electronic Parking Brake (EPB) found not operating to specification - EPB may not hold the car effectively - Parking brake components showing signs of wear - Parking brake warning light may also be evident within the DIP (See example shown in Figure 1. Technical background: The issues described can be evident due to the car being driven in Transport mode with the EPB applied during the Transit process Or In some cases similar symptoms may be seen whilst in service.
2062259/42022-04-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; SUSPENSION. Air suspension warning light within the DIP - DTC's P089200 - C104707 - C103B13 - Evident within Address 74. Customer statement / workshop findings: Air suspension warning light within the DIP Workshop findings: One or a combination of the DTCs shown below are evident within address 74 - P089200 - Symptom Code 3145792 - TCM Power Relay Sense Circuit Intermittent (Level Control Valves Open Circuit) - C103B13 - 3145909 - Solenoid for level control system Open circuit - C104707 - 3211279 - Level control valves mechanical malfunction Technical background: Refer to the Measure section of this TPI.
2066236/12022-04-06. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Unintended sounding of the Alarm siren - Following activation of the ignition or whilst the vehicle is left standing. Customer statement / workshop findings: Unintended sounding of the alarm siren following activation of the ignition Or Unintended sounding of the alarm siren whilst the vehicle is left standing Workshop findings. The following DTCs could also be evident within diagnostic address 0046 and/or 00BB and/or 00BC - B131DF5: alarm system siren supply voltage lower limit value less than - B131D29: sirens / alarm horn for anti-theft warning system Range/Performance - B131D29: anti-theft alarm system siren / alarm horn signal, not valid Technical background: In the event the symptom(s) described are evident, please refer to the instructions within the Measure section of this TPI
2065896/12022-03-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Rotating screen alignment. Customer statement / workshop findings: The gap and fit between the veneer face facia panel of the Bentley rotating display (BRD) and the passenger and drivers side fascia panels may differ from one side to the other Depending on vehicle specification, the chrome brightware strip on the veneer face facia panel of the Bentley Rotating Display (BRD) may appear to be misaligned with the chrome strips on the passenger and/or drivers side fascia panels If the minimum functional gap is not maintained, the operation of the (BRD) unit can be compromised Technical background: The chrome brightware strip is fixed to the veneer face fascia panel (with no separate adjustment) and as such can appear to be misaligned. The veneer face fascia panel relies on fixed location pins that may be out of tolerance Referring to the Measure section, rework the veneer face fascia panel to align the chrome brightware strip and/or the gapping between the BRD and the passenger and drivers side fascia panels If the BRD is partially rotated and unresponsive (e.g not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled
2065894/12022-03-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. Rotating display/screen - Fault diagnosis for operational complaints. Customer statement / workshop findings: Various rotating display operational complaints. The operative should ensure the correct TPI is followed depending on the actual issue(s) as follows: - TPI 2065895/- Rotating display/screen noise - Diagnosis for complaints relating to noise during operation/during a drive cycle, should be considered for any issues which relate to noise issues - TPI 2065896/- Rotating screen alignment IMPORTANT: The Rotating screen alignment TPI should be considered for any issues which relate to noise and overall functionality. HINT: Alignment abnormalities may cause functionality/noise issues - TPI 2065897/- Rotating display inoperative (Rotating display may fail to function or get stuck in one position) should be considered for vehicles up to and including VIN SCBCA13S3KC073865 If the Bentley rotating Display (BRD) is partially rotated and unresponsive (e.g. not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen - However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled NOTE: For all other Bentley rotating display (BRD) operational issues, the operative should follow the remaining instructions within the Measure section of this TPI
2065922/12022-03-04. Service bulletin. EQUIPMENT:ELECTRICAL:INFOTAINMENT:VIDEO (TOUCH)SCREEN/MONITOR/UNIT; ELECTRICAL SYSTEM; SUSPENSION. Bentley dynamic ride system warning displayed - DTC P0B2600 with symptom code 28672. Customer statement / workshop findings: Bentley dynamic ride system fault warning displayed within the DIP Workshop findings: DTC P0B2600 (Hybrid Battery A Voltage High) with Symptom Code 28672. Measure: 1) Refer to Rep.Gr 27 - Replace the Super capacitor 2) Once the work is complete - Raise a non technical DISS query confirming the issue is now resolved

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.