Service bulletins for the 2019 Bentley Continental
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
828 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 2061171/7 | 2022-07-09. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. New Continental GT/GTC and New Flying Spur - V8 Kovomo - Fuel Pressure Regulation - Numerous DTCs. Customer statement / workshop findings Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: - P310B00 Low Fuel Pressure Regulation with symptom code 2636 - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - P018B00 - Fuel Pressure Sensor B Circuit Range/Performance with symptom code 17871 - Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues Technical background In the event the customer complaint relates to the following: - Customer experienced poor start up - proceed with the remaining instructions NOTE: The operative must gather information regarding the Customer experience regarding when the issue occurred for example: Pre- conditions, warning lights and driveability at time issue occurred, details when the vehicle was last refuelled and the grade of fuel used The operative must now use the information contained within the Measure section to determine the correct analysis and repair procedure |
|---|---|
| 2067403/1 | 2022-07-08. Service bulletin. SUSPENSION. Knocking noise from the front (Driving over an uneven road surface) - Front trailing arm bush found damaged/leaking. Customer statement / workshop findings: Knocking noise from the underside of the vehicle (front) when driving on uneven road surfaces Workshop findings: Front trailing arm bush found damaged/leaking as shown in Figures 1 and 2 Technical background: If the customer complaint and symptoms are as described - Refer to the instructions within the Measure section of this TPI |
| 2061857/4 | 2022-07-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Headlamp switch - Inoperative/Not illuminated - DTC U110B00 within 09-Central Electrics (BCM1). Customer statement / workshop findings: Headlamp switch - Inoperative/Not illuminated Workshop findings - DTC U110B00 within 09-Central Electrics (BCM1) as shown in Figure 1 Figure 1 - Yellow warning light/message within the DIP (Adaptive Lighting Fault) NOTE: Some lighting functionalities can in some cases be lost for example: - Rear fog light activation - All weather lighting mode activation - Headlamps default to dipped beam however high beam will still activate manually NOTE: Recycling the ignition will not resolve the problem Technical background: The issue will not occur when the ignition is on and/or the vehicle is being driven. It occurs as the headlamp switch goes into a “sleep” state after ignition is Switched OFF, the issue is then evident to the driver when the ignition is next switched ON. |
| 2058423/8 | 2022-07-06. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. New Continental GT/GTC, New Flying Spur and Bentayga - Low Oil Pressure Warning During Early Vehicle Life. Customer statement / workshop findings: Warning on the Driver Instrument Panel (DIP) - Oil pressure too low DTCs relating to oil pressure may also be stored within the Master ECU. Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU). Measure: VERY IMPORTANT: Prior to conducting the onward instructions, the following symptoms MUST be evident - Warning on Driver Instrument Panel (DIP) Oil pressure too low And/or - Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU) Should any of the afore mentioned not be evident and the symptoms cannot be reproduced No further action should be taken unless the issue can be reproduced or demonstrated by the customer In the event the symptom/s are evident please conduct the onward Diagnosis Instructions |
| 2055036/5 | 2022-06-02. Service bulletin. ELECTRICAL SYSTEM. My Bentley - Connected services. Customer statement / workshop findings: Complaints relating to My Bentley connected services. Technical background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query. My Bentley support have access to additional admin tools and systems to help resolve any queries; and also have the ability to raise DISS technical queries if required. |
| 2066669/1 | 2022-05-07. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Engine coolant - Overheat condition - Warning evident within the DIP - DTC's P2B6500 and P2B8600 are evident. Customer statement / workshop findings: - Engine cooling system overheating And/or - Coolant loss And/or - Warning light in Drivers Information Panel (DIP) The following DTCs may also be evident within 0001 and/or 0011 - P2B6500 and/or P2B8600. |
| 2064582/3 | 2022-05-07. Service bulletin. ELECTRICAL SYSTEM; SUSPENSION. Vehicle sitting low on one or more corners when static with no relevant DTCs stored. Customer statement / workshop findings: - Vehicle sitting low on one or more corners when static - No relevant DTC’s are evident Technical background: Refer to the Measure section of this TPI |
| 2066481/1 | 2022-05-07. Service bulletin. SUSPENSION. Squeaking noise from the front suspension when driving on uneven road surfaces. Customer statement / workshop findings: Squeaking noise from the front suspension when driving on uneven road surfaces Technical background: Refer to the videos which are on the Bentley Hub referencing TPI 2066481/- |
| 2066852/1 | 2022-05-07. Service bulletin. ELECTRICAL SYSTEM. Shaker speaker - Diagnostic checks. Customer statement / workshop findings: Customer complains of poor quality music output from the shaker speaker due to a rattling noise/sound distortion. Technical background: There have been instances where shaker speakers have been changed under warranty for the complaint of sound distortion, yet when tested by Bentley motors and the supplier, no fault could be found with the returned unit. Measure: To ascertain the difference between distortion or a rattle emanating from a loose/surrounding component Or The shaker speaker itself is incorrectly secured and/or at fault please conduct the following steps before replacing any components |
| 2062035/6 | 2022-05-07. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. New Continental GT and GTC - Repeat window drop glass concerns. Customer statement: - Incorrect operation of the front and rear drop door glass functionality - Front and/or rear drop door glass fails to open/close or attempts to close and reopens once contact has been made between the glass and applicable seal Workshop findings: - DTCs for window regulator motor no basic setting B148754 evident within any of the 4 window control modules (diagnostic address 42, 52, BB and BC) for loss of basic settings Technical background: A customer complaint of windows failing to open/close correctly Including The loss of Basic Settings DTC must be evident before proceeding |
| 2065398/2 | 2022-05-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. W12 TSI - Engine MIL light illuminated with numerous DTC's within 0001 including - P032700 and/or P033200. Customer statement: - MIL light displayed - Engine not refined when running Workshop findings The two most common DTCs are as follows: - P032700 - Knock sensor 2 Circuit Low input - address 01 (Engine control module 1) - P033200 - Knock sensor 1 Circuit Low input - address 01 (Engine control module 1) Technical background: In the event the symptoms and/or DTCs are evident the operative should refer to the instructions within the Measure section. |
| 2063678/3 | 2022-04-08. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. P245000 - EVAP System Switching Valve "A" Performance/Stuck Open DTC logged - V8 Kovomo. Customer statement / workshop findings: Emission control system warning light illuminated within the DIP (Figure 1). Workshop findings: DTC P245000 - EVAP System Switching Valve "A" Performance/Stuck Open - With symptom code 11952 Technical background: Refer to the Measure section of this TPI |
| 2064338/2 | 2022-04-08. Service bulletin. ELECTRICAL SYSTEM:WIRING; SUSPENSION; ELECTRICAL SYSTEM. Warning light illuminated within the DIP - DTC C103711 - Evident within Address 74. Customer statement / workshop findings: Air suspension warning light within the DIP Workshop findings: The DTC shown below is evident within address 74 - C103711 - Right rear level control system sensor Short circuit to Ground - C103316 - Right sensor voltage supply for vehicle levelling Voltage too low Technical background: Previous instances have highlighted the following after inspection: - Broken wires - Kinked wiring - Loose Rear Right Height sensor G77connection - Defective Rear Right Height sensor G77 |
| 2066393/1 | 2022-04-08. Service bulletin. ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SENSORS; ELECTRICAL SYSTEM. PDC system not working or PDC system false detection. Customer statement / workshop findings: - PDC system not working or PDC system false detection - Warning evident within the DIP (Figure 1). Workshop findings: Parking aid sensor Range/Performance DTCs evident within numerous control units Technical background: Refer to the Measure section of this TPI. |
| 2052349/8 | 2022-04-08. Service bulletin. AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE; ELECTRICAL SYSTEM; SEAT BELTS. Front seatbelt - Diagnostic Trouble Codes - B130474 and/or B130574. Customer statement / workshop findingsL Diagnostic Trouble Codes (DTCs) evident in Address: 0015 System name: 15 - Airbag Control Module B130474: Left front seat belt tensioner control module Actuator deviated B130574: Right front seat belt tensioner control module Actuator deviated The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings. Technical background: Dummy seat belt buckles of any description MUST NOT be used under any circumstances, Figure 1 shows an example of a dummy seat belt buckle |
| 2062184/5 | 2022-04-08. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE:ELECTRICAL; PARKING BRAKE. Electronic Parking Brake (EPB) functionality issues. Customer statement / workshop findings: The following issues could be evident during PDI or found whilst in service - Electronic Parking Brake (EPB) found not operating to specification - EPB may not hold the car effectively - Parking brake components showing signs of wear - Parking brake warning light may also be evident within the DIP (See example shown in Figure 1. Technical background: The issues described can be evident due to the car being driven in Transport mode with the EPB applied during the Transit process Or In some cases similar symptoms may be seen whilst in service. |
| 2062259/4 | 2022-04-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; SUSPENSION. Air suspension warning light within the DIP - DTC's P089200 - C104707 - C103B13 - Evident within Address 74. Customer statement / workshop findings: Air suspension warning light within the DIP Workshop findings: One or a combination of the DTCs shown below are evident within address 74 - P089200 - Symptom Code 3145792 - TCM Power Relay Sense Circuit Intermittent (Level Control Valves Open Circuit) - C103B13 - 3145909 - Solenoid for level control system Open circuit - C104707 - 3211279 - Level control valves mechanical malfunction Technical background: Refer to the Measure section of this TPI. |
| 2052785/7 | 2022-04-08. Service bulletin. SERVICE BRAKES, HYDRAULIC. Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Service: Note: For correct diagnosis and repair the attached Flowchart must be followed. 1. Check the overall condition of the brakes to determine if the brake noise can be attributed to one of the causes listed in the Technical Background section of this TPI. If the noise is not a result of one these causes, proceed with point 2. 2. Record the noise and frequency For the frequency analysis and the noise recording we recommend using the Chassis Ear Tool WT 10437. To record the noise and measure the frequency using WT 10437 Chassis Ear Tool follow these instructions; Refer to File recording in the WT 10437 user instructions. |
| 2066236/1 | 2022-04-06. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Unintended sounding of the Alarm siren - Following activation of the ignition or whilst the vehicle is left standing. Customer statement / workshop findings: Unintended sounding of the alarm siren following activation of the ignition Or Unintended sounding of the alarm siren whilst the vehicle is left standing Workshop findings. The following DTCs could also be evident within diagnostic address 0046 and/or 00BB and/or 00BC - B131DF5: alarm system siren supply voltage lower limit value less than - B131D29: sirens / alarm horn for anti-theft warning system Range/Performance - B131D29: anti-theft alarm system siren / alarm horn signal, not valid Technical background: In the event the symptom(s) described are evident, please refer to the instructions within the Measure section of this TPI |
| 2066580/1 | 2022-04-06. Service bulletin. SERVICE BRAKES. Odour emanating from the front wheel arches/front wheels - Odour is also evident within the cabin. Customer statement / workshop findings: - Undesirable odour emanating from the front wheel arches, the issue occurs after the vehicle has reached normal operating temperature - The odour can also be evident within the cabin Technical background: HINT: The issue described is mainly evident on low mileage/low use vehicles with iron brakes In the event the symptoms are as described, please conduct the instructions within the Measure section of this TPI |
| 2065896/1 | 2022-03-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Rotating screen alignment. Customer statement / workshop findings: The gap and fit between the veneer face facia panel of the Bentley rotating display (BRD) and the passenger and drivers side fascia panels may differ from one side to the other Depending on vehicle specification, the chrome brightware strip on the veneer face facia panel of the Bentley Rotating Display (BRD) may appear to be misaligned with the chrome strips on the passenger and/or drivers side fascia panels If the minimum functional gap is not maintained, the operation of the (BRD) unit can be compromised Technical background: The chrome brightware strip is fixed to the veneer face fascia panel (with no separate adjustment) and as such can appear to be misaligned. The veneer face fascia panel relies on fixed location pins that may be out of tolerance Referring to the Measure section, rework the veneer face fascia panel to align the chrome brightware strip and/or the gapping between the BRD and the passenger and drivers side fascia panels If the BRD is partially rotated and unresponsive (e.g not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled |
| 2065897/1 | 2022-03-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Rotating display inoperative (Rotating display may fail to function or stick in one position). Customer statement / workshop findings: The Bentley Rotating Display (BRD) fails to rotate Or The BRD sticks in one position Technical background: The afore mentioned symptoms can be caused by a poor connection within the motor wiring harness Please ensure the symptom(s) are as described before proceeding If the BRD is partially rotated and unresponsive (e.g. not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen However, Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled |
| 2065894/1 | 2022-03-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. Rotating display/screen - Fault diagnosis for operational complaints. Customer statement / workshop findings: Various rotating display operational complaints. The operative should ensure the correct TPI is followed depending on the actual issue(s) as follows: - TPI 2065895/- Rotating display/screen noise - Diagnosis for complaints relating to noise during operation/during a drive cycle, should be considered for any issues which relate to noise issues - TPI 2065896/- Rotating screen alignment IMPORTANT: The Rotating screen alignment TPI should be considered for any issues which relate to noise and overall functionality. HINT: Alignment abnormalities may cause functionality/noise issues - TPI 2065897/- Rotating display inoperative (Rotating display may fail to function or get stuck in one position) should be considered for vehicles up to and including VIN SCBCA13S3KC073865 If the Bentley rotating Display (BRD) is partially rotated and unresponsive (e.g. not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen - However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled NOTE: For all other Bentley rotating display (BRD) operational issues, the operative should follow the remaining instructions within the Measure section of this TPI |
| 2065922/1 | 2022-03-04. Service bulletin. EQUIPMENT:ELECTRICAL:INFOTAINMENT:VIDEO (TOUCH)SCREEN/MONITOR/UNIT; ELECTRICAL SYSTEM; SUSPENSION. Bentley dynamic ride system warning displayed - DTC P0B2600 with symptom code 28672. Customer statement / workshop findings: Bentley dynamic ride system fault warning displayed within the DIP Workshop findings: DTC P0B2600 (Hybrid Battery A Voltage High) with Symptom Code 28672. Measure: 1) Refer to Rep.Gr 27 - Replace the Super capacitor 2) Once the work is complete - Raise a non technical DISS query confirming the issue is now resolved |
| 2065895/1 | 2022-03-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Rotating display/screen noise - Diagnosis for complaints relating to noise during operation and/or during a drive cycle. Condition: Various rotating display/screen noises during operation Technical Background: If the Bentley Rotating display (BRD) is partially rotated and unresponsive (e.g. not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled The symptoms listed below are listed as a guideline to enable the applicable noise issue to be diagnosed and repaired, in the event the noise and/or symptom does not match any of the Scenarios listed below, the operative should raise a DISS query and await feedback before conducting any further work |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.