Service bulletins for the 2019 Bentley Continental
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
828 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| 2062626/3 | 2022-08-31. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. DTCs stored for all cylinders on Bank 1 or all cylinders on Bank 2 - W12 TSI engine derivative. Customer statement / workshop findings: -DTCs stored for all cylinders on Bank 1 or all cylinders on Bank 2 including multiple cylinder misfires DTC - Misfires logged in one or both engine control units - Engine warning light on - Erratic engine operation Technical background: -Refer to the Measure section of this TPI -This TPI is applicable to all W12 TSI models including W12 TSI Speed models |
|---|---|
| 2065919/2 | 2022-08-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Water leaking from mechanical water pump - Low coolant level warning displayed - W12 TSI. Customer statement / workshop findings: - Coolant leaking from the mechanical coolant pump And/or - Low coolant level warning displayed Technical background: The operative MUST ensure the instructions within the Measure section are followed, the instructions differ slightly depending on the part number of the mechanical coolant pump (B or C suffix). |
| 2061171/7 | 2022-07-09. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. New Continental GT/GTC and New Flying Spur - V8 Kovomo - Fuel Pressure Regulation - Numerous DTCs. Customer statement / workshop findings Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: - P310B00 Low Fuel Pressure Regulation with symptom code 2636 - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - P018B00 - Fuel Pressure Sensor B Circuit Range/Performance with symptom code 17871 - Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues Technical background In the event the customer complaint relates to the following: - Customer experienced poor start up - proceed with the remaining instructions NOTE: The operative must gather information regarding the Customer experience regarding when the issue occurred for example: Pre- conditions, warning lights and driveability at time issue occurred, details when the vehicle was last refuelled and the grade of fuel used The operative must now use the information contained within the Measure section to determine the correct analysis and repair procedure |
| 2058423/8 | 2022-07-06. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. New Continental GT/GTC, New Flying Spur and Bentayga - Low Oil Pressure Warning During Early Vehicle Life. Customer statement / workshop findings: Warning on the Driver Instrument Panel (DIP) - Oil pressure too low DTCs relating to oil pressure may also be stored within the Master ECU. Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU). Measure: VERY IMPORTANT: Prior to conducting the onward instructions, the following symptoms MUST be evident - Warning on Driver Instrument Panel (DIP) Oil pressure too low And/or - Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU) Should any of the afore mentioned not be evident and the symptoms cannot be reproduced No further action should be taken unless the issue can be reproduced or demonstrated by the customer In the event the symptom/s are evident please conduct the onward Diagnosis Instructions |
| 2066669/1 | 2022-05-07. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Engine coolant - Overheat condition - Warning evident within the DIP - DTC's P2B6500 and P2B8600 are evident. Customer statement / workshop findings: - Engine cooling system overheating And/or - Coolant loss And/or - Warning light in Drivers Information Panel (DIP) The following DTCs may also be evident within 0001 and/or 0011 - P2B6500 and/or P2B8600. |
| 2065398/2 | 2022-05-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. W12 TSI - Engine MIL light illuminated with numerous DTC's within 0001 including - P032700 and/or P033200. Customer statement: - MIL light displayed - Engine not refined when running Workshop findings The two most common DTCs are as follows: - P032700 - Knock sensor 2 Circuit Low input - address 01 (Engine control module 1) - P033200 - Knock sensor 1 Circuit Low input - address 01 (Engine control module 1) Technical background: In the event the symptoms and/or DTCs are evident the operative should refer to the instructions within the Measure section. |
| 2063678/3 | 2022-04-08. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. P245000 - EVAP System Switching Valve "A" Performance/Stuck Open DTC logged - V8 Kovomo. Customer statement / workshop findings: Emission control system warning light illuminated within the DIP (Figure 1). Workshop findings: DTC P245000 - EVAP System Switching Valve "A" Performance/Stuck Open - With symptom code 11952 Technical background: Refer to the Measure section of this TPI |
| 2065894/1 | 2022-03-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. Rotating display/screen - Fault diagnosis for operational complaints. Customer statement / workshop findings: Various rotating display operational complaints. The operative should ensure the correct TPI is followed depending on the actual issue(s) as follows: - TPI 2065895/- Rotating display/screen noise - Diagnosis for complaints relating to noise during operation/during a drive cycle, should be considered for any issues which relate to noise issues - TPI 2065896/- Rotating screen alignment IMPORTANT: The Rotating screen alignment TPI should be considered for any issues which relate to noise and overall functionality. HINT: Alignment abnormalities may cause functionality/noise issues - TPI 2065897/- Rotating display inoperative (Rotating display may fail to function or get stuck in one position) should be considered for vehicles up to and including VIN SCBCA13S3KC073865 If the Bentley rotating Display (BRD) is partially rotated and unresponsive (e.g. not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen - However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled NOTE: For all other Bentley rotating display (BRD) operational issues, the operative should follow the remaining instructions within the Measure section of this TPI |
| 2065919/1 | 2022-03-02. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Water leaking from mechanical water pump - Low coolant level warning displayed - W12 TSI. Workshop findings: - Coolant leaking from the mechanical coolant pump And/or - Low coolant level warning displayed Technical background: The operative MUST ensure the instructions within the Measure section are followed, the instructions differ slightly depending on the part number of the mechanical coolant pump (B or C suffix). |
| 2066040/1 | 2022-03-02. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Oil leak from the oil separator/breather connection - Intake manifold whistle - Emission control warning within the DIP. Customer statement / workshop findings: - Emission control warning within the DIP And/or - Whistling noise(s) from the Inlet manifold Workshop findings: Oil leak between the oil separator tank and the Bank 1 breather line connection (Figure 1) NOTE: Oil leak detection spray is evident within Figure1, the use of detection spray in the example shown highlights the location of the leak. Measure: 1) Referring to Rep.Gr 17 - Gain access to the oil separator tank 2) Referring to Figure 2 - Replace the following parts and all associated parts as detailed within the applicable Rep.Gr and the ETKA parts catalogue |
| 2058423/7 | 2022-03-01. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. New Continental GT / GTC, New Flying Spur and Bentayga - Low Oil Pressure Warning During Early Vehicle Life. Customer statement / workshop findings: Warning on the Driver Instrument Panel (DIP) - Oil pressure too low DTCs relating to oil pressure may also be stored within the Master ECU. Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU). Measure VERY IMPORTANT: Prior to conducting the onward instructions, the following symptoms MUST be evident - Warning on Driver Instrument Panel (DIP) Oil pressure too low And/or - Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU) Should any of the afore mentioned not be evident and the symptoms cannot be reproduced. No further action should be taken unless the issue can be reproduced or demonstrated by the customer. In the event the symptom/s are evident please conduct the onward Diagnosis Instructions |
| 2065398/1 | 2022-01-07. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. W12 TSI - Engine MIL light illuminated with numerous DTCs within 0001 including - P032700 and/or P033200. Customer statement - MIL light displayed - Engine not refined when running Workshop findings The two most common DTCs are as follows: - P032700 - Knock sensor 2 Circuit Low input - address 01 (Engine control module 1) - P033200 - Knock sensor 1 Circuit Low input - address 01 (Engine control module 1) Please note: The DTCs listed are the two most common DTCs (seen to date) although other DTCs may be evident depending on the failure mode (including the boost control solenoid and crankcase ventilation heater DTCs) |
| 2065215/1 | 2021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. V8 Kovomo engine replacement (Fitment of ancillary components). Customer statement / workshop findings: Torque values for ancillary components (used during engine replacement) are not currently available within the Repair manual. The affected components and torque values are as listed within the Technical background section of this TPI. Measure: Refer to the Technical background section |
| 2064964/2 | 2021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Vehicle vibration/humming at idle - Active Engine Mount leak. Customer statement / workshop findings: Vehicle vibration/humming noise at idle Technical background: - Left and/or right hand Active Engine Mount leaking oil (see the examples shown in Figures 1,2 and 3). Measure 1) Refer to Rep.Gr.10 Engine mounts -To remove and fit - Replace the left and right hand (BOTH) Active Engine Mounts |
| 2064964/1 | 2021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Vehicle vibration/humming at idle - Active Engine Mount leak. Customer statement / workshop findings: Vehicle vibration/humming noise at idle Technical background: - Left and/or right hand Active Engine Mount leaking oil (see the examples shown in Figures 1,2 and 3) Measure: 1) Refer to Rep.Gr.10 Engine mounts -To remove and fit - Replace the left and right hand Active Engine Mounts |
| 2053348/5 | 2021-11-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. W12 Engine management light on - Turbocharger speed sensor DTCs stored. Customer statement / workshop findings; - The engine management light is on. Workshop findings: The customer statement can be reproduced. Either of the following DTCs are stored in address 01 Engine Control Module 1 or address 11 Engine Control Module 2 - P257900: Turbocharger Speed Sensor A - Circuit Range/Performance Or - P259400: Turbocharger Speed Sensor B - Circuit Range/Performance Or - P259500: Turbocharger Speed Sensor B - Circuit low |
| 2062016/2 | 2021-11-05. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Rough running & potentially poor start up performance - MIL light on - Possible misfires Customer statement: -The Engine management light is on -Rough running and potentially poor start up performance and/or -Engine misfires Very Important: Should the afore mentioned symptoms and/or DTCs be evident with NO misfires reported the operative MUST raise a DISS query and await feedback from Product Support before conducting any further work Technical background: Debris in the fuel system can lead to a blockage in the low pressure fuel injectors, ultimately causing a cylinder misfire. |
| 2064776/1 | 2021-11-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Customer statement / workshop findings -Engine misfiring -Engine running rough (not refined) -Engine misfire DTCs evident -Engine management light illuminated within the DIP -Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) IMPORTANT: The symptoms described are typically evident during early life stages of vehicle use (between 100Km and 250Km) |
| 2064679/1 | 2021-11-05. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:SOLENOID/ACTUATOR. Customer statement / workshop findings Oil leaking out of the tell tale hole from the following fixings: -CDA activation/ deactivation solenoid fixings -Or Fuel rail fixings -Or Fixings for the vacuum system assembly Technical background: Shows oil leaked which had leaked from the tell tale hole at the top of the fixing. Upgraded fixings prevent oil leaks from the tell hole. |
| 2063678/2 | 2021-10-07. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. P245000 - EVAP System Switching Valve "A" Performance/Stuck Open DTC logged - V8 Kovomo. Customer Statement: Emission control system warning light illuminated within the DIP. Workshop findings: DTC P245000 - EVAP System Switching Valve A Performance/Stuck Open - With symptom code 11952 Technical Background: Refer to the Measure section of this TPI. |
| 2059489/2 | 2021-10-07. Service bulletin. ENGINE; SEAT BELTS. New Cont GT & GTC V8 - Start-Stop System Inhibit - Driver's Seat Belt Start/Stop system inhibit - Drivers seatbelt unfastened. Customer statement / workshop findings: The Start/Stop system functions with the drivers seat belt not fastened although the Owners handbook states that the drivers seat belt must be fastened for the Start/Stop system to function. Technical background On all 202 0model year vehicles specified with a V8 engine, the Start/Stop system will function with the drivers seat belt not fastened although the Owners handbook states the drivers seat belt must be fastened for the Start/Stop system to work, the system in this scenario is functioning correctly. Due to a change to one of the system inhibits, the 2021 model year Owners handbooks will be updated to confirm the Start/Stop system will work with the seat belt unfastened. |
| 2053429/4 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Emission control system lamp illuminated - DTC P044100 evident. Customer statement / workshop findings: Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within one or both engine control modules. Technical background: Should DTC P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow be evident (static or intermittent) within one or both Engine control modules please refer to the instructions within the Measure section of this TPI |
| 2053351/7 | 2021-10-06. Service bulletin. ENGINE AND ENGINE COOLING; STRUCTURE. Buzzing noise from engine area. Customer statement / workshop findings Workshop findings: Buzzing noise heard at idle from the sump area when the vehicle is elevated on a workshop ramp. The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances. Technical background: A buzzing noise can be generated by the oil pump when the engine is running at idle. Measure: Test a comparable vehicle with the same Engine derivative. If the same noise is apparent on the comparable vehicle and no oil pressure warnings or relevant DTCs are stored then the noise can be considered a characteristic of the vehicle and no further action should be taken. |
| 2057978/5 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Engine Lubricating Oil - Replenishment. Customer statement / workshop findings Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services. Technical background: In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified running-in periods consume more oil during the running-in period, and the oil consumption will stabilize after the running-in period. Refer to the Owners Manual for specific running-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Certain driving conditions may negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods |
| 2060205/3 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Engine Cooling System - DTC P218100 - V8 Kovomo Customer statement / workshop findings: Emission Control Lamp illuminated on Driver Instrument Panel. The time to reach the correct engine coolant operating temperature has increased. Diagnostic Trouble Code(DTC) P218100 -Cooling System Performance is stored in the Engine Control Module (ECM), the vehicle warm up time is longer when compared to other vehicles of the same type. Technical background: It is possible for the engine coolant Thermostat to corrode overtime, this corrosion is due to an adverse reaction of the Thermostat material with the engine coolant. The corrosion and subsequent build-up of debris prevents the correct operation of the thermostat when closing, resulting in over cooling. The ECM triggers a DTC when the target engine temperature is outside of the specified parameter. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.