Service bulletins for the 2011 Bentley Continental
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
169 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 2056582/3 | 2020-08-05. Service bulletin. STRUCTURE. Interior trim - Creak and rattle - Noise identification. Customer statement / workshop findings: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work |
|---|---|
| 2053492/6 | 2020-08-05. Service bulletin. SUSPENSION:REAR:SPRINGS. Air spring fault finding. Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. TheMeasure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. These checks should be carried out in conjunction with the Elsapro procedure Air suspension: To check with the use of the special tool Air suspension leak tester VAS 751 001 shown in the image below as item ( 1). Refer to Elsapro, Repair Group 43, Air suspension To check. |
| 2058465/2 | 2020-07-07. Service bulletin. STRUCTURE. Continental GTC - Hood insulation cover checks prior to replacement Customer statement / workshop findings: Should any of the following components require replacing: -Convertible hood insulation pad -Convertible hood outer cover -Convertible hood inner lining Refer to the onward instructions within this TPI Technical background: Please refer to the instructions within the Measure section of this TPI to check/confirm if the insulation pad is damaged prior to replacement IMPORTANT: In the event the insulation pad is found to be at fault please refer to TPI 2058277/1 |
| 2053177/10 | 2020-07-07. Service bulletin. ELECTRICAL SYSTEM. All Vehicle Variants - Spurious DTC List Condition: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken. |
| 2058277/2 | 2020-03-04. Service bulletin. STRUCTURE. Continental GTC - Hood insulation pad tension strap fitting procedure Condition In the event the insulation pad (ARROW - Figure 1) requires replacing, the onward instructions within this TPI must be followed Technical Background The right and left hand tension straps (Figure 2) are no longer fitted at the time of manufacture, the Measure section within this TPI details the procedure which must be followed to fit the tension straps |
| 2058465/1 | 2020-03-04. Service bulletin. STRUCTURE. Continental GTC - Hood insulation cover checks prior to replacement Customer statement / workshop findings: Should any of the following components require replacing: Convertible hood insulation pad Convertible hood outer cover Convertible hood inner lining Refer to the onward instructions within this TPI Technical background: Please refer to the instructions within the Measure section of this TPI to check/confirm if the insulation pad is damaged prior to replacement IMPORTANT: In the event the insulation pad is found to be at fault please refer to TPI 2058277/1 |
| 2036267/1 | 2020-03-03. Service bulletin. ELECTRICAL SYSTEM. HVAC Potential spurious Diagnostic Trouble Code (DTC) Customer statement / workshop findings: Customer will not be aware of this code / Workshop may discover this code whilst running a Diagnostic Trouble Code log as part of other investigations on the car Technical background: At low ambient temperatures a spurious fault code may be logged by the HVAC control module in reference to the air quality sensor. The code is stored without being accompanied by any functional failure in the system Measure: The following may be seen during routine interrogation of vehicle systems do not take any investigative action in response to the following fault code unless there is an actual fault evident in the system or a fault in the system has been reported by the owner. |
| 2058173/1 | 2020-02-08. Service bulletin. ELECTRICAL SYSTEM. Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI |
| 2058349/1 | 2020-02-08. Service bulletin. ELECTRICAL SYSTEM. Front roof console replacement - Continental Flying Spur Technical background: Front roof control module with the part numbers listed below are no longer programmed by Bentley Motors prior to dispatch 3W5 959 527 AH0DN 3W5 959 527 AL0DN The programming procedure within the Measure section must be followed |
| 2058277/1 | 2020-02-08. Service bulletin. STRUCTURE. Customer statement / workshop findings In the event the insulation pad (ARROW - Figure 1) requires replacing, the onward instructions within this TPI must be followed. Technical background The right and left hand tension straps (Figure 2) are no longer fitted at the time of manufacture, the Measure section within this TPI details the procedure which must be followed to fit the tension straps. |
| 2033745/2 | 2020-01-17. Service bulletin. LATCHES/LOCKS/LINKAGES; ELECTRICAL SYSTEM. Bentley Continental Series - Power boot close switch - Correct diagnosis Customer statement / workshop findings: Boot lid does not attempt to power close when the boot close switch (located on the inside of the boot lid) is pressed. Technical background: In the event the power boot does not attempt to close when the boot close switch is pressed please check the applicability of the model and VIN shown in the Production change section of this TPI before commencing. |
| 2038035/1 | 2020-01-17. Service bulletin. ELECTRICAL SYSTEM. Continental Series, Flying Spur and Mulsanne - Main harness identification Customer statement / workshop findings: Should an issue be diagnosed or reported regarding any part of the vehicles main harness or engine harness resulting in a requirement to raise a DISS ticket, please follow all instructions within this TPI to ensure that your Bentley Motors Technical Service Centre (TSC) receives all required and relevant information. Technical background: In order for the Bentley Motors Technical Service Centre (TSC) to resolve any issues relating to the vehicles main harness or engine harness please follow the instructions within this TPI. Refer to Section 1 for the main vehicle harness identification label location Refer to Section 2 for the engine harness identification label location |
| 2042104/1 | 2020-01-17. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns Customer statement / workshop findings: An improved feedback method is required should a complaint of telephone functionality / quality be reported. Technical background: A minimum standards document is required to capture an accurate description of customer telephone issues. Measure: The attached document should be completed and attached to the relevant DISS query, this will allow a full understanding of the customer complaint and the circumstances in which the complaint becomes apparent. |
| 2036134/3 | 2020-01-17. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. W12 Engine and Transmission Control Module Update (SC14/01) Technical background: New replacement software for the engine control modules and the transmission control module has been created to address customer satisfaction issues concerning driveability. Remedy: This Campaign must be carried out on all vehicles within the affected VIN range to ensure the latest specification engine and transmission software is installed. The software update within this campaign has been devised to ensure all W12 engine derivative vehicles within the specified VIN range have the latest level of software installed within the engine control modules and the transmission control module. |
| 2056407/2 | 2020-01-09. Service bulletin. STEERING; SUSPENSION. Condition: Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if any TPIs are applicable to the customers complaint/issue, should an applicable TPI be available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required) For correct diagnosis and repair, the attached Flowchart must be followed in conjunction with the Measure section of this TPI |
| 2051187/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Condition: Poor engine running, reduced power, engine warning lamp illuminated. Technical Background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfires. Service: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place. |
| 2056582/2 | 2020-01-09. Service bulletin. STRUCTURE. Condition: Customer statement: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if there are any TPIs which are applicable to the customers complaint/issue if there is an applicable TPI available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required). For correct diagnosis and repair the attached Flowchart must be followed in conjunction with the Measure section of this TPI |
| 2052785/4 | 2020-01-09. Service bulletin. SERVICE BRAKES, HYDRAULIC. Condition: Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). 6. Discs have a groove in them (Figure 2) 7. There is chemical contamination on the braking surface of the disc due to a wheel or tyre cleaner being sprayed directly onto the disc (Figure 3). 8. There are pad marks on the brake disc as a result of the brake pad material transferring to the discs. This can occur when a vehicle has been stood for long periods of time in a wet or snowy environment (Figure 4). |
| 2053177/6 | 2020-01-09. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Condition: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken. |
| 2053492/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM; SUSPENSION. Condition: The front and/or rear suspension appears to have dropped. Technical Background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. Please follow and complete the check list within the Measure section of this TPI to help in diagnosing the issue (the check list does not need to be sent as an attachment should a DISS technical query be raised) . Should a leak be found from an air spring, compressor, valve unit or reservoir, please raise a DISS technical query and include as much information as possible including photograph/s of the leak/s location. Once the DISS ticket has been submitted please await clarification from your TSC before commencing with replacing any of the suspected faulty air springs. Mandatory reporting is applicable for all air spring related issues. |
| 2051562/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM. Condition: 12 Volt Battery test instruction Technical Background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2053177/5 | 2020-01-09. Service bulletin. EQUIPMENT. Customer statement / workshop findings: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Measure: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken. |
| 2056392/1 | 2019-11-07. Service bulletin. ELECTRICAL SYSTEM. Customer statement / workshop findings: When selecting to update the date (Figure 1) and time (Figure 2) by GPS, the two features will no longer automatically update via GPS. Technical background: A reset to the GPS network has meant the automatic GPS date and time feature no longer functions. |
| 2036678-2 | 2019-09-23. Service bulletin. EQUIPMENT. Speaker Replacement - Diagnostic checks |
| 2053492.4 | 2019-07-01. Service bulletin. SUSPENSION. Air spring fault finding |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.