Service bulletins for the 2013 Audi S6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
835 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| A371309 2028715- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted. |
|---|---|
| A351313 2030477- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 35 number 13-10 dated May 7, 2013. The following message appears in the information display: "Gearbox malfunction: you can continue driving". Fault entries are stored in the transmission control module. Fault codes and expanded environmental conditions codes must match exactly or this TSB should not be followed. Poor internal contact area on circuit board will lead to faults. Oil additives can cause the plastic circuit plates to delaminate, causing contact loss. |
| A941306 2017806- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared. |
| A911374 2024323- | 2017-11-17. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions. |
| A481336 2033044- | 2017-11-17. Service bulletin. STEERING; STEERING:ELECTRIC POWER ASSIST SYSTEM. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case. A solution is in development and will be made available as soon as possible. The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality. Refer to the attached Information and Q&A document for guidance when handling each case. |
| A441337 2030275- | 2017-11-17. Service bulletin. SUSPENSION; STEERING. Supersedes Technical Service Bulletin Group 44 number 12-34 dated November 13, 2012. Customers may report the following conditions on vehicles with less than 6000 miles. In some cases these conditions may be noticed at PDI. Vehicle pulls - left or right. Steering wheel not leveled or off-center. If the alignment concern is due to outside influence (e.g. accident), this TSB does not apply. |
| A441336 2022563- | 2017-11-17. Service bulletin. SUSPENSION. Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control. |
| A011369 2028344- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300°C (572°F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies. |
| A481342 2033044- | 2017-11-17. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 48 number 13-39 dated March 18, 2013. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case. A solution is in development and will be made available as soon as possible. The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality. |
| A431314 2018765- | 2017-11-17. Service bulletin. SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM; SUSPENSION:FRONT:SPRINGS:AIR SUSPENSION SYSTEM. Supersedes Technical Service Bulletin Group 43 number 12-11 dated October 29, 2012. The self-leveling system can no longer be adjusted with the MMI. The compressor for the self-leveling system continues to run after the engine has been switched off and the vehicle has been locked. DTCs may be stored in the level control system module, J197 (address word 34). Because of poor performance or failure of the air suspension compressor, the vehicle ride height cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected. |
| A351309 2028085- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 35 number 12-07 dated December 21, 2012. Customer may report that there is oil leaking under the vehicle. There are a number of possible sources for the leak. Leaking from the oil pan seal. Crack in the oil pan. Leak between gearbox housing and intermediate housing. The source of the leak may be confused with o-ring of drain plug. |
| A271317 2033524- | 2017-11-17. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. "Set" button on cruise control stalk does not work. DTCs are present in the vehicle. Incorrect tolerances of cruise control "Set" button. |
| A001348 2002047- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center |
| A191335 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A481338 2033044- | 2017-11-17. Service bulletin. STEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING. Supersedes Technical Service Bulletin Group 48 number 13-36 dated February 21, 2013. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case. A solution is in development and will be made available as soon as possible.The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality. Refer to the attached Information and Q&A document for guidance when handling each case. |
| A481339 2033044- | 2017-11-17. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 48 number 13-38 dated March 18, 2013. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case.A solution is in development and will be made available as soon as possible. The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality. Refer to the attached Information and Q&A document for guidance when handling each case. |
| A911380 2032706- | 2017-11-17. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 13-73 dated January 25, 2013. Customer complains of a "popping" noise from the radio followed by 10-15 seconds of no audio. The concern can happen in any audio source. Vehicle is equipped with MMI 3G or MMI 3G+ infotainment systems. Vehicle is not equipped with Bose or Bang & Olufsen sound systems. An ignition cycle is not required for audio to resume.The problem originates in the HD radio code, which can create a "resetting" within the radio unit. Because the tuner is always active in the background, the problem can occur regardless of the audio source or if the HD radio is on or off. It can also occur at any point that the MMI is on, but not necessarily active. For example, the customer opens a door and the MMI starts up. Even though the system is not ?on? because the ignition is not active, the tuner is running and can create the effect. |
| Email Mandatory | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. |
| A961501 2019260- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A911517 2042013- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM recovery activation will not remedy the concern. |
| A871570 2041717- | 2017-11-17. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Any replacement of A/C compressors?regardless of the reason for failure?must include an ODIS GFF cooling performance test plan of the A/C system with documentation of the recovered refrigerant volume. This GFF test plan requirement is mandatory without exception. |
| A351518 2028085- | 2017-11-17. Service bulletin. STRUCTURE:BODY. Supersedes Technical Service Bulletin Group 35 number 13-12 dated June 18, 2013. Customer may report that there is oil leaking under the vehicle. Leaking from the oil pan seal. Crack in the oil pan. Leak between gearbox housing and intermediate housing. The source of the leak may be confused with o-ring of drain plug. |
| A191562 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A171565 2038129- | 2017-11-17. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
| Scheduled Maint | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Thereafter, all remaining scheduled services are due every 10,000 miles or 1 year after previous service, whichever occurs first. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.