Service bulletins for the 2013 Audi Q7
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1239 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Electrical system are shown. Show all
| A011542 2041787- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. DTCs are stored in the ECM. There may be soot buildup on the moveable elements of the pressure sensing glow plug (PSG). |
|---|---|
| A911521 2039476- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 15-06 dated July 28, 2015. The customer complains that the Audi connect online service in their 2011-2013 A8, 2012-2013 Q7, or 2013 A4, A5, A5 cabriolet, or Q5 vehicle only reaches 2G service. This bulletin applies only to model year 2011-2013 A8, 2012-2013 Q7, and 2013 A4, A5, A5 cabriolet, and 2013 Q5 vehicles. For 2012-2013 A6 and A7 vehicles see TSB 2039515. This bulletin does not apply to model year 2014 and newer. Starting with model year 2014, the new telephone module was installed in production. The model year 2014 A8 is not included in this repair. Model year 2014 was the last year before the A8 product improvement and ElsaPro may classify these vehicles as model year 2013 because these vehicles are the same from a technical and design standpoint. But unlike the model year 2013 vehicles, the model year 14 vehicles already have the updated telephone module in the MMI. Recently, T-Mobile (the service provider for Audi connect) has repurposed some of the GSM spectrum (3G on 2100Mhz band) to maximize 4G LTE coverage in certain metropolitan areas. Devices that do not support 3G service on the 1900MHZ band (including MMI main units of the vehicles to which this bulletin applies) will only receive 2G service when the switch is completed. The change currently only affects the markets listed above, but will affect other markets in coming years. This bulletin will be updated to include these markets as changes occur. |
| A911529 2013422- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A171568 2028440- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY. Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A011305 2033919- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 13-03 dated May 29, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. |
| A011306 2033919- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 13-05 dated June 7, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. |
| A011309 2014753- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives. |
| A011311 2033919- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 13-06 dated June 18, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. |
| A961364 2029384- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 96 number 12-32 dated April 27, 2012. The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer function. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer?s transmitter operates at 295Mhz. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. No DTCs are stored in any control units. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming. |
| A941296 2027773- | 2017-11-08. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS; EQUIPMENT; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 12-69 dated March 15, 2012. Part or all of the daytime running lights do not work on vehicles with LED DRLs. For vehicles with halogen DRLs, please reference TSB 2017488, 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only. |
| A941298 2028277- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS; EQUIPMENT. Supersedes Technical Service Bulletin Group 94 number 12-91 dated October 24, 2012. Considerable moisture present in headlamp. The moisture disappears only after extended drives (greater than 10 minutes). No external damage to headlamp which could introduce moisture. Humid air settles on the inside of the glass, causing moisture to appear on the inside of the headlamp lens. Because of the headlamp circulation system, outside air is allowed to flow through the headlamps. The open, water-protected ventilation system (needed for pressure compensation) creates different ? climate zones? inside the headlamp, where the lens is either warmed up by the light or cooled down by passing air. When high air humidity and temperature differences exist between the inside of the headlamps and the outside, condensation can form on the inside of the lens, especially in cold and wet weather. The moisture in the headlamps can be compared with condensation on the windshield, which is cleared by the "defroster vent". This moisture buildup can happen for example: after a car wash, after steam cleaning of the engine or the front end, or after overnight temperature changes. This condition is more easily visible with headlamps made from clear glass. The moisture is an optical condition which does not affect the headlamp function (light performance) and does not lead to corrosion nor does it lead to damage of the internal headlamp parts. This condition is common to all exterior vehicle lights, and can occur on every headlamp, fog lamp, or rear lamp. |
| A941299 2029194- | 2017-11-08. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 12-74 dated April 23, 2012 . The customer complains the high beams do not function on one side or one of the low beams flickers intermittently. In addition to this, an ? Adaptive Headlight Defective? warning can be present in the cluster if the vehicle has the Prestige trim level. DTCs are set in the 09 ? Central Electric Control Unit or in the 55 ? Headlamp Range Control Unit depending on the trim level of the vehicle. Vehicles with the Premium Plus option package can have the DTC set in the 09 module. Vehicles with the Prestige option package can have the DTC set in the 55 module. One or more of the connectors inside the headlamp housing are disconnected fully or partially from the factory. |
| A571278 2031413- | 2017-11-08. Service bulletin. SEATS; ELECTRICAL SYSTEM. The seat memory does not work. The MMI displays that the memory function is not active. The seat memory control unit can be deactivated due to voltage fluctuations in the vehicle? s power system, or from a large static discharge through the seat cover. If the seat memory control unit is deactivated due to the above mentioned influences, the control unit cannot be reactivated through any vehicle controls, vehicle keys, or through the normal GFF test plans. It can only be reactivated with special test plans within the tester. |
| A571279 2018737- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Supersedes Technical Service Bulletin Group 57 number 10-32 dated September 9, 2010. Customer may complain that the vehicle locks itself when removing the key from the ignition lock. When removing the ignition key from the ignition, the customer may unintentionally operate the lock button of the remote key. With the S contact in the ignition lock off (key is removed), the central locking will resume to respond to signals from the remote key. MVB 17 in electric control unit address $46 (Comfort System Central Control Module) can be used for argumentation. The last received central locking command is stored in this MVB. A value of ?2? indicates a locking command last sent from the remote key. With the Autolock feature, MVB 17 is overwritten. Therefore MVB 17 must be read immediately after the complaint. |
| A911263 2021151- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle. |
| A901238 2032113- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc. |
| A911270 2032240- | 2017-11-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. The Google Earth map will not load. The display shows an active data connection, and ? Google? is almost fully white. Customer has active Audi Connect subscription. All other Audi Connect functions operate normally. The concern only occurs if the vehicle is started in a 2G cellular zone. The system operates normally if started in a 3G cellular zone. The vehicle has MMI software 0566 installed. Certain Audi Connect partner carriers are transmitting data that is not supported by the MMI. The data disrupts the loading process of Google Earth and causes it to not completely load. |
| A941200 2024877- | 2017-11-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 12-83 dated July 9, 2012. Warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 / 14 (Control unit faulty) is registered in the dynamic headlight range control unit, address word 55. Both headlights function normally. Vehicles equipped with adaptive (cornering) lighting. New software version 0010 in the dynamic headlight range control module addresses this condition. If the headlight range control module has a software version lower than 0010 installed, then use the SVM code listed in Service to update the module. Some control units will already have software version 0010 installed but can still exhibit the conditions mentioned above. When this occurs, the software will need to be reflashed using a separate SVM code. The corrupt software will be overwritten. The software version does not change after the update. |
| A571402 2022032- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A011485 2036761- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 14-71 dated March 13, 2014. The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective. |
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
| E-mail-3.0L TDI | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. 3.0L TDI Settlement Program Update |
| A011479 2033379- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 13-42 dated November 21, 2013. DTC P164D00 is stored in the engine control module. Red oil pressure warning light may be on. An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be reduced. |
| A481459 2017266- | 2017-11-08. Service bulletin. STEERING; ELECTRICAL SYSTEM; POWER TRAIN. Supersedes Technical Service Bulletin Group 48 number 13-51 dated August 30, 2013. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.