Service bulletins for the 2009 Audi Q7
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
700 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| A911263 2021151- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle. |
|---|---|
| A901238 2032113- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc. |
| A941200 2024877- | 2017-11-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 12-83 dated July 9, 2012. Warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 / 14 (Control unit faulty) is registered in the dynamic headlight range control unit, address word 55. Both headlights function normally. Vehicles equipped with adaptive (cornering) lighting. New software version 0010 in the dynamic headlight range control module addresses this condition. If the headlight range control module has a software version lower than 0010 installed, then use the SVM code listed in Service to update the module. Some control units will already have software version 0010 installed but can still exhibit the conditions mentioned above. When this occurs, the software will need to be reflashed using a separate SVM code. The corrupt software will be overwritten. The software version does not change after the update. |
| A571402 2022032- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
| E-mail-3.0L TDI | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. 3.0L TDI Settlement Program Update |
| A371423 2028472- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 12-38 dated February 22, 2012. The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. On vehicles with Audi advanced key, the vehicle cannot be locked by remote control after the engine has been switched off. DTC 00230 may be sporadically stored in the vehicle authorization system control module. The Park position of the gear shifter is sporadically not recognized, which causes the ignition key to not be cleared and prevents the vehicle from being locked. |
| A911448 2036482- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. The volume of the radio, navigation announcements, or output of the Bluetooth telephone system changes when the ignition is switched off, then switched back on, the volume is muted, then unmuted, and the MMI is switched off by a long press of the volume knob, then restarted without an ignition cycle. All vehicles with MMI 2G/3G/3G+/MIB Navigation are affected. |
| A481459 2017266- | 2017-11-08. Service bulletin. STEERING; ELECTRICAL SYSTEM; POWER TRAIN. Supersedes Technical Service Bulletin Group 48 number 13-51 dated August 30, 2013. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment. |
| A971443 2036764- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A911437 2030947- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding. |
| A271424 2025360- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. |
| A171449 2028440- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A971442 2036764- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A971441 2036764- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A911419 2026895- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle. |
| A011350 2030192- | 2017-11-03. Service bulletin. ELECTRICAL SYSTEM; STEERING; POWER TRAIN; EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 01 number 12-55 dated October 22, 2012. MIL on. DTCs are stored in the engine control module (ECM). Engine may have reduced power without significant loss of power or stalling. A deformed oil seal behind the potentiometer causes a linkage of the intake manifold flap adjustment to stick, which sets the DTCs. When the potentiometer is removed, the oil seal can be seen. |
| A971338 2016275- | 2017-11-03. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 10-14 dated September 16, 2010. Electrical components associated with the panorama roof, power rear lid, interior lighting, or Central Electrics (such as sunroof frame/sunshade operation, power rear lid operation with open/close switch, dome light operation, etc.) may become inoperative. The battery may be discharged. This bulletin only applies to vehicles with panorama roofs. During vehicle assembly, the wire harness that is routed along the left side of the sunroof frame may be pinched at one of the sunroof frame to body assembly points. |
| Update Bulletin | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ELECTRICAL SYSTEM:SOFTWARE. This Update is in effect until removed. Procedure is valid only for vehicles that show the 23H3 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be in Federal Emissions Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. ECM Software update to address customer satisfaction issues. |
| A911304 2013422- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A571397 2022032- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A271319 2029010- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. |
| A271318 2023282- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed. |
| A911598 2018187- | 2017-10-27. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.