WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Audi A8

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1506 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
37 14 30 20036582022-05-02. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC):CONTROL MODULE:SOFTWARE; POWER TRAIN. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
37 14 29 20290272022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. The DTCs are stored due to an issue with the transmission control module software.
37 14 28 20362782022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. Calibration of the transmission control module software. Rough downshifts when the vehicle is slowed to a stop.
37 14 25 20285612022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; POWER TRAIN. New software in the gear shift control module addressed the condition. There is no customer complaint about the gearbox. The gear lever display flashes. The following message is shown: "gearbox problem, journey can be continued with restrictions". This is a generic message in the instrument cluster that a transmission fault has occurred and Limp Home Mode might be activated if the malfunction continues.
37 14 22 20289852022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; UNKNOWN OR OTHER; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). The fault occurs with ATF temperature below 60° C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
37 14 20 20362782022-05-02. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. Rough downshifts when the vehicle is slowed to a stop. Calibration of the transmission control module software.
37 13 99 20290272022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: - DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). - DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. - DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.
37 13 97 20289852022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER. The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
37 13 84 20293052022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; UNKNOWN OR OTHER. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration concerns. Further TCM software calibration to improve shift concerns.
37 13 82 20285612022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. New software in the Selector Lever Control Module (J587) addressed the condition. The gear lever display flashes. The message "gearbox problem, journey can be continued with restrictions" is shown.
37 13 80 20289852022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. DTC P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM. Customer may report transmission warning lamp illuminated in instrument cluster.
37 13 79 20293052022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Further TCM software calibration to improve shift concerns.
37 13 78 20316752022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). The entry P060A00 with DFCC 12480 can be logged in the TCM. This fault is only a diagnostic error. The fault will not affect vehicle performance.
37 13 17 20290272022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). ? DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. ? DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.
37 13 09 20287152022-05-02. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:GEARS. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
37 13 07 20336582022-05-02. Service bulletin. SERVICE BRAKES. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. As a result, application of the brake and accelerator pedals at the same time (brake pedal with left foot and accelerator pedal with right foot) results in the following: ? Brake pedal function (normal at all times) overrides any throttle application. ? Diagnostic Trouble Codes (DTCs) will not be stored. ? When the brake pedal is applied while the accelerator is depressed, engine RPMs will return to idle speeds of 1400 RPMs after approximately two seconds. ? When the accelerator is applied while the brake pedal is depressed, the vehicle accelerates slower than usual (reduced engine torque).
37 13 06 20285612022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. New software in the gear shift control module addressed the condition.
37 13 04 20285612022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. New software in the gear shift control module addressed the condition.
37 13 02 20290272022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). ? DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. ? DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.
37 13 01 20289852022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
37 12 73 20317752022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. Customer may report transmission warning lamp illuminated in instrument cluster. DTC P074100 (Torque Converter Clutch Circuit Performance or Stuck Off) is stored in TCM. Diagnostic error in TCM software.
37 12 72 20289852022-05-02. Service bulletin. ELECTRICAL SYSTEM:ADAS:HUD:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer may report transmission warning lamp illuminated in instrument cluster. Fault code P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM.
27 14 24 20253602022-05-02. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. For additional information on known current draw issues, refer to the following TSBs: ? 2014127: 27 Battery dead or low after returning to the vehicle (2007 A6, A8, Q7) ? 2019143: 27 Battery discharged on some vehicles with Advanced Key (2005 - 2008 A6, Q7)
27 14 23 20363922022-05-02. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.
27 14 22 20363922022-05-02. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.