Service bulletins for the 2012 Audi A6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1506 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| A441450 2022563- | 2017-11-08. Service bulletin. SUSPENSION; STEERING: STEERING WHEEL/HANDLE BAR. Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. |
|---|---|
| A391414 2028902- | 2017-11-08. Service bulletin. STRUCTURE:BODY. Supersedes Technical Service Bulletin Group 39 number 12-12 dated June 12, 2012. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft. |
| A371430 2003658- | 2017-11-08. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. |
| A371424 2037127- | 2017-11-08. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. A jerky accelerator response is felt when the vehicle is pulled away from a stop in reverse. Incorrect calibration of clutch program. |
| A371422 2028985- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 13-01 dated April 24, 2013. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A011477 2030580- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY. Supersedes Technical Service Bulletin Group 01 number 14-51 dated January 3, 2014. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition. |
| A001463 2033576- | 2017-11-08. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage. |
| Customer Letter | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Audi has determined that, under specific conditions, the turbocharger could malfunction and may cause the Malfunction Indicator Lamp (MIL) on the instrument cluster to illuminate due to the presence of specific fault codes caused by this component. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions. Dealers will diagnose and replace a faulty turbocharger if necessary, at no cost to you as long as the vehicle remains within the time and mileage limits of this warranty extension. |
| A911447 2028446- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Supersedes Technical Service Bulletin Group 91 number 14-45 dated June 20, 2014. MMI screen carrier shudders, shakes, and/or is noisy during operation. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). For vehicles with Radio Plus, please follow standard diagnosis steps. The applicable vehicles can be clearly identified by the MMI touch interface pad on the control panel. Incorrect tolerances with the carrier slide mechanism can disrupt the travel of the screen. |
| A911445 2028446- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Supersedes Technical Service Bulletin Group 91 number 13-05 dated September 12, 2013. MMI screen carrier shudders, shakes, and/or is noisy during operation. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). For vehicles with Radio Plus, please follow standard diagnosis steps. The applicable vehicles can be clearly identified by the MMI Touch touchpad on the E380. Incorrect tolerances with the carrier slide mechanism. |
| A741420 2035757- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; SEATS. Supersedes Technical Service Bulletin Group 74 number 14-17 dated February 21, 2014. Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D). No leak is present. There is a software issue in the seat pneumatics control modules that causes the seat pneumatics to automatically actuate in high altitudes (change in air pressure) or in fluctuating temperatures in order to maintain pressure. |
| A201434 2035073- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 20 number 14-32 dated March 21, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A191450 2025303- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A971443 2036764- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A961483 2034000- | 2017-11-08. Service bulletin. LANE DEPARTURE: ASSIST; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-78 dated October 31, 2013. Audi side assist deactivates or is sporadically inoperative. Message "Side Assist Unavailable" is displayed in the driver information system display when the system deactivates. Audi side assist deactivates or is sporadically inoperative. DTCs are stored in the Lane change assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi side assist temporarily. |
| A911438 2033780- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple® devices with the new 8-pin plug will not play videos using the Audi Music Interface. The current Apple devices have a new plug assignment: the 30-pin plug has been replaced with an 8-pin plug. The old plug used an analog video transmission, whereas the new plug uses a digital video transmission that is not supported by the Audi Music Interface. |
| A911437 2030947- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding. |
| A911436 2027903- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-55 dated August 13, 2012. The most recent calls are not shown in the call lists of the vehicle. Call lists are not shown. The phone book (Directory) in the vehicle is not updated. The phone book is not downloaded to the vehicle. Vehicles with MMI 3G+ are affected. |
| A911435 2026895- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 91 number 14-19 dated January 3, 2014. Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle. |
| A911434 2027718- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 91 number 14-20 dated January 3, 2014. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver's voice sounds muffled, as if it is being heard from under water. The microphone seal was damaged during installation into the roof module. |
| A901448 2030903- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 90 number 12-35 dated October 1, 2012. Customer complains that when the vehicle is driven, various warning lights illuminate, sometimes with restricted functions in the electrical system. The complaint occurs with another complaint regarding the MMI 3G+ infotainment system. After an ignition cycle, the condition is gone and therefore, it may not be reproducible. Sporadic DTCs may be present for communication errors, restricted functions, or missing/incorrect messages. |
| A871449 2020124- | 2017-11-08. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 87 number 13-44 dated August 26, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure.The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. |
| A701437 2029280- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 70 number 14-36 dated March 31, 2014. The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse. |
| A461478 2036688- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module. According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. |
| A441449 2022563- | 2017-11-08. Service bulletin. SUSPENSION. Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.