Service bulletins for the 2012 Audi A6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1506 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Transmission and driveline are shown. Show all
| Dealer Letter - | 2017-12-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This communication is to inform you of upcoming Update 37J1. On Audi A6 and A7 vehicles with 8 speed automatic transmissions manufactured within a specific period, problem which affects the shifting comfort may occur in isolated cases. Update the TCM software to the latest level with SVM. |
|---|---|
| Update Bulletin | 2017-12-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. On Audi A6 and A7 vehicle with 8 speed automatic transmissions manufactured within a specific period, problem which affects the shifting comfort may occur in isolated cases. This Update is in effect until removed. Procedure is valid only for vehicles that show the 37J1 code in the Elsa Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. |
| A371449 2037127- | 2017-12-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 14-24 dated May 1, 2014. A jerky accelerator response is felt when the vehicle is pulled away from a stop in reverse. Incorrect calibration of clutch program. |
| A371448 2030007- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced. No faults are stored. TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. |
| A371310 2034863- | 2017-12-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION. Customer may report that the gearbox warning message is on. DTC P0706 (driving mode sensor, implausible signal) is stored in the transmission control module (TCM), J217 (address 02). There is a reaction between the TCM and the automatic transmission fluid (ATF) in vehicles within a specific VIN range. |
| A371309 2028715- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted. |
| A371395 2030582- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 37 number 13-89 dated February 11, 2013. Customer may report that the transmission warning light comes on. There are no drivability/starting concerns. GFF scan shows fault code P060600 (Control Module Malfunctioning, Sporadic) stored in the transmission control module, J217 (02). The entry is caused by an overly sensitive diagnosis in the transmission control module. |
| A371391 2032941- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer may report transmission warning light comes on. No drivability/starting concerns. GFF scan shows fault code: P172400 Starter Interlock Signal - short to Ground (GND) Sporadic, stored in the Transmission control module (02). Fault code: 00165 Transmission Park/Neutral Position Switch -F322- Incorrect Signal Sporadic, may also be stored in the Comfort module (46). Momentary loss of signal under very specific driving conditions causes fault to set. |
| A371389 2030582- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 12-61 dated August 20, 2012. Customer may report that the transmission warning light comes on. There are no drivability/starting concerns. GFF scan shows fault code P060600 (Control Module Malfunctioning, Sporadic) stored in the transmission control module. The entry is caused by an overly sensitive diagnosis in the transmission control module. |
| A371388 2032094- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. Supersedes Technical Service Bulletin Group 02 number 12-02 dated December 6, 2012. Customer may report transmission warning light comes on. No drivability/starting concerns. GFF scan shows fault code: P060300 (Control Module Malfunctioning, Sporadic), stored in the Transmission control module (02). The entry is caused by an overly sensitive diagnosis in the gearbox control unit. This does not affect the driving characteristics. |
| A371386 2028985- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. Supersedes Technical Service Bulletin Group 37 number 13-85 dated February 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 "Torque Converter Clutch Circuit Performance" or "Stuck Off" is stored in TCM. The fault occurs with ATF temperature below 60o C. Check for this temp range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A371385 2028985- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Supersedes Technical Service Bulletin Group 37 number 13-80 dated January 16, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 "Torque Converter Clutch Circuit Performance" or "Stuck Off" is stored in TCM. The fault occurs with ATF temperature below 60o C. Check for this temp range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A371305 2030582- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 13-95 dated February 26, 2013. Customer may report that the transmission warning light comes on. There are no drivability/starting concerns. DTC P060600 (Control Module Malfunctioning, Sporadic) is stored in the transmission control module (TCM), J217 (02). The entry is caused by an overly sensitive diagnosis in the transmission control module. |
| A371303 2033653- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer may report transmission warning light comes on. No drivability/starting concerns. GFF scan shows DTC P172400 (Control Module Malfunctioning, Sporadic), stored in the transmission control module (TCM), J217 (02). DTC 00165 (Transmission Park/Neutral Position Switch -F322- Incorrect Signal Sporadic) may also be stored in the comfort system central control module, J393 (46). The entry is caused by an overly sensitive diagnosis in the TCM, due to an error in the engine control module (ECM), J623, software. This error does not affect the driving characteristics. |
| A371301 2028985- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 13-97 dated March 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A371397 2028985- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 13-86 dated February 6, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module, J217 (03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A661330 2030471- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length. |
| A021202 2032094- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Customer may report transmission warning light comes on. No drivability/starting concerns. GFF scan shows fault code- P060300 (Control Module Malfunctioning, Sporadic), stored in the Transmission control module (02). The entry is caused by a too sensitive diagnosis in the gearbox control unit. This does not affect the driving characteristics. |
| A371277 2029027- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-67 dated September 28, 2012. Customer may report gearbox warning light on. In some cases after starting vehicle and placing into gear the vehicle would not move. After key cycle the vehicle drives without restriction. The entry P060A00 with DFCC 8692 can be logged in the following situation: After selecting Neutral, a driving mode (D or R) is selected within one second while the vehicle rolls (at under 2 mph). This can, for example, happen when maneuvering the vehicle into or from a parking area. The entry P060A00 with DFCC 8694 can be logged when quickly changing from P-N because of a low diagnosis threshold. The entry P060A00 with DFCC 12480 can be logged because of a low diagnosis threshold when changing gear with the tip function. |
| Audi TAC Technic | 2017-11-08. Service bulletin. POWER TRAIN; STEERING. This document contains the Audi TAC technical newsletter. The news letter contains information on the Audi TAC hours of operation, the Audi technical assistance survey, the 4.0 L V8 TFSI in the A8L, S6, S7, S8, and the power steering control unit. |
| A371434 2028985- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 14-22 dated May 1, 2014. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A371430 2003658- | 2017-11-08. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. |
| A371422 2028985- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 13-01 dated April 24, 2013. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A971442 2036764- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| Executive Servic | 2017-10-27. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; SERVICE BRAKES, HYDRAULIC:FLUID; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID. This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.