Service bulletins for the 2010 Audi A5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
892 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| A171565 2038129- | 2017-11-17. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
|---|---|
| A171567 2027731- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 15-60 dated April 24, 2015. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 2.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions; for example: stop-and-go traffic with extended idle periods. |
| A191340 2033491- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-36 dated April 15, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak. |
| A191341 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A211314 2031245- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Supersedes Technical Service Bulletin Group 21 number 13-13 dated April 4, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure Deviation). |
| A211210 2031245- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ELECTRICAL SYSTEM. Mil on, DTC P0299 Negative Pressure Deviation. Turbocharger waste gate flap has play. Under certain driving conditions the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap which sets the DTC P0299 Negative Pressure Deviation. |
| A001463 2033576- | 2017-11-08. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage. |
| A211418 2031245- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 21 number 13-16 dated July 9, 2013. The MIL is on. DTC P029900 (Negative Pressure Deviation) is stored as a static fault in the engine control module (ECM), J623 (address word 01). Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P029900 (Negative Pressure Deviation). |
| A191450 2025303- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A971441 2036764- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A011463 2033630- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced. |
| Reference-Oil Ca | 2017-11-03. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the Audi oil capacity chart. |
| A871346 2035582- | 2017-11-03. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. |
| Dealer Letter-Up | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:IGNITION; ENGINE. This communication is to inform you of upcoming Update 28G6. There are 79,232 Audi vehicles affected in the U.S. by this Update. Rough idle or reduced driving power and, in turn, an illuminated Malfunction Indicator Lamp (MIL) on the instrument cluster due to the presence of specific fault codes caused by this component. Inspect and replace ignition coils as required. |
| A191346 2033491- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-44 dated July 18, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak. |
| A011348 2033001- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-37 dated October 10, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. |
| A871345 2024644- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS. Supersedes Technical Service Bulletin Group 87 number 13-41 dated May 30, 2013. Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose. |
| A101310 2018288- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
| A011330 2027082- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 24 number 12-28 dated April 24, 2012. MIL on. DTC P0234 (Turbo/Super Charger Overboost Condition) is stored in the engine control module, J623 (address word 01). No other DTCs are stored. DTC P0234 can be set inadvertently by the software application. DTC P0234 can be set with an actual cause in combination with loss of engine power and low/uneven engine performance, based on charge pressure control. |
| A011329 2033223- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-73 dated March 7, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once. |
| A171343 2027731- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 13-42 dated October 10, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 2.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions; for example: stop-and-go traffic with extended idle periods. |
| A171342 2027731- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 12-05 dated March 20, 2012. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 2.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions; for example: stop-and-go traffic with extended idle periods. |
| A011337 2033001- | 2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-24 dated August 20, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. |
| Executive Servic | 2017-10-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; SERVICE BRAKES, HYDRAULIC:FLUID; ENGINE AND ENGINE COOLING; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID; POWER TRAIN. This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service. |
| A171563 2038129- | 2017-10-27. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.