WenmarOpen by Wenmar Pro

Over-the-air update ECG-26.2.11.4.1 Edge

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeOver-the-air update
NHTSA id11033809
Published by NHTSA2026-06-13
Manufacturer's numberECG-26.2.11.4.1 Edge
Manufacturer's date2026-06-09
Campaign id or software versionECG-26.2.11.4.1
NHTSA componentELECTRICAL SYSTEM; UNKNOWN OR OTHER

NHTSA's summary

Quality improvements include: - Enhanced system performance, disk usage limits and memory monitoring

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system

Vehicles listed
FORD EDGE2021, 2022, 2023, 2024

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SSM 552212026-10-12. Service bulletin. For 20222026 vehicles equipped with a 8F35 transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, and/or D>R) should be noted in the warranty claim. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
SSM 550312026-07-28. Service bulletin. Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
SSM 550282026-07-28. Service bulletin. Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.
SYNC-26.2.8.3 Edge2026-06-30. Over-the-air update. Quality improvements include: -Privacy robustness updates
TSB 26-22972026-06-29. Service bulletin. Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
SYNC-26.2.0.16.2 Edge2026-04-28. Over-the-air update. 26S09 Recall Remedy -Update to enable rearview camera image to display when in reverse after infotainment screen thermal shutdown
SSM 547202026-04-10. Service bulletin. Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
SYNC-25.1.7.10.1 Edge2026-03-03. Over-the-air update. "25S49 Recall Remedy: -Infotainment software update to address frozen screens"
SSM 546012026-02-27. Service bulletin. Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SYNC-25.2.0.16.1 Edge2026-02-05. Over-the-air update. "Quality Improvements Include: - Bug Fixing and Feature improvements. - Resolves black screen issue caused when there is no SiriusXM disk space."