WenmarOpen by Wenmar Pro

Service bulletin TSB 25-2613

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11027609
Published by NHTSA2026-01-13
Manufacturer's numberTSB 25-2613
Manufacturer's date2026-01-08
NHTSA componentSUSPENSION; UNKNOWN OR OTHER

NHTSA's summary

This article supersedes TSB 24-2408 to update the parts list. Some of the vehicles listed in the Model statement above may exhibit a loud front end clink/clunk noise that leads to the identification of a cracked or broken front differential frame mount bracket. This may be due to flexing of the front differential from driving in 4L for extended periods of time. Note: Advise the customer that 4L/Rock Crawl drive mode should only be used when necessary, as using 4L when not necessary can cause damage to the vehicle. Refer to the Owner's Manual for additional information.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Suspension

Vehicles listed
FORD BRONCO2021, 2022, 2023, 2024

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
25V3100002025-05-09. SUSPENSION:FRONT:CONTROL ARM:UPPER BALL JOINT
25V3080002025-05-09. SUSPENSION:FRONT:CONTROL ARM:LOWER ARM
20250202025-01-17. Suspension
25V0250002025-01-17. SUSPENSION:REAR:SHOCK ABSORBER
24V7700002024-10-16. SUSPENSION:FRONT:CONTROL ARM:UPPER BALL JOINT

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
TSB 26-23802026-09-29. Service bulletin. This article supersedes TSB 25-2575 to update the Parts list to add the applicable body wiring harnesses and underbody shield bolts. Some vehicles listed in the Model statement above may exhibit a "Sta-bar Disconnect Service Required" message in the instrument panel cluster (IPC) with any of the following diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM): C103A, C1A99, C1B03, C1B07, C1B14 and/or B1A67. This may be due to water intrusion in the stabilizer bar wiring harness connector.
TSB 25-25752025-12-02. Service bulletin. This article supersedes TSB 24-2104 to update the vehicle model years affected. Some vehicles listed in the Model statement above may exhibit a "Sta-bar Disconnect Service Required" message in the instrument panel cluster (IPC) and an illuminated warning light with any of the following diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM): C103A, C1A99, C1B03, C1B07, C1B14 and/or B1A67. This may be due to water intrusion in the stabilizer bar wiring harness connector.
SSM 538692025-06-11. Service bulletin. Some 2021-2024 Bronco vehicles built on or before 01-Jan-2025 equipped with a 2.3L EcoBoost engine and 10R60 automatic transmission may exhibit diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, and P0304 and may be accompanied by a buck/jerk sensation while driving between 35-55 mph (56-89 km/h) in gears 7-10. If the condition remains after normal engine misfire diagnostics and associated repairs have been performed, the condition may be related to driveline torsional vibration induced by the rear wheels and/or rear axle assembly. The driveline torsional harmonics/vibrations are incorrectly identified by the misfire monitor as an engine misfire. Perform standard road force wheel balancing of all four tire and wheel assemblies and retest. If the condition continues to occur, replace the ring and pinion gearset in the rear axle. For claiming, use causal part 4209 and applicable labor operations found in Section 04 of the Service Labor Time Standards (SLTS) Manual.
TSB 24-21042024-05-02. Service bulletin. This article supersedes TSB 23-2400 to update the parts list. Some 2021-2023 Bronco vehicles may encounter a Sta-bar Disconnect Service Required message in the instrument panel cluster and an illuminated warning light with diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM)
SSM 518632023-09-02. Service bulletin. During replacement of the electronic front stabilizer bar disconnect assembly on 2021-2023 Bronco vehicles, removal and replacement of the sta-bar harness is required. To assist engineering with root cause analysis of failed sta-bar disconnect assemblies, include the sta-bar harness with the part in the same package when returning warranty replacement sta-bar disconnect assembly. The sta-bar disconnect assembly return should also be packaged in the original box with all protective insulators in place to properly protect it during shipping. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report with photos attached (if possible) for any front stabilizer bar disconnect concerns.