WenmarOpen by Wenmar Pro

Service bulletin TSB 25-2526

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11024548
Published by NHTSA2025-10-29
Manufacturer's numberTSB 25-2526
Manufacturer's date2025-10-29
NHTSA componentUNKNOWN OR OTHER; POWER TRAIN

NHTSA's summary

Some of the vehicles listed in the model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P226D stored in the powertrain control module (PCM). This may be due to having the incorrect gas particulate filter pressure sensor assembly installed.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Trouble codes named

P226D

Vehicles listed
FORD BRONCO SPORT2025
FORD MAVERICK2025

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20256912025-12-12. Powertrain
25V8630002025-12-12. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:PARK PAWL

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 552212026-10-12. Service bulletin. For 20222026 vehicles equipped with a 8F35 transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, and/or D>R) should be noted in the warranty claim. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
TSB 26-24282026-10-02. Service bulletin. This bulletin supersedes 25-2326. Reason for update: update the service procedure to include the fuel tank isolation valve replacement, update the causal part number, and increase the labor time allowance to include the fuel tank isolation valve replacement. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM and/or the fuel tank isolation valve.
TSB 26-24282026-10-02. Service bulletin. This bulletin supersedes 25-2326. Reason for update: update the service procedure to include the fuel tank isolation valve replacement, update the causal part number, and increase the labor time allowance to include the fuel tank isolation valve replacement. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM and/or the fuel tank isolation valve.
TSB 26-24142026-09-14. Service bulletin. This article supersedes 26-2058 Reason for update: update the TSB title and TSB issue to include new DTCs Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Intermittent or permanent no reverse (R) engagement * Illuminated MIL with DTC P0767 or P0765:7E stored in the powertrain control module (PCM) In addition to the required conditions, the vehicle may also exhibit a harsh reverse engagement, P0766, P0765:7F, P0736 and/or P2703 stored in the PCM. This may be due to an internal mechanical concern with the selectable one-way clutch (SOWC).
SSM 550582026-08-03. Service bulletin. Some 2025-2026 Maverick vehicles built on or before 05-Dec-2025 and 2024-2026 Nautilus vehicles built on or before 04-Sep-2025 may exhibit limited power and display "Stop Safely Now" or "Service Vehicle Soon" stored in the message center after start up with diagnostic trouble codes (DTC) P0A5D, P0A60, P0A63, P0A6F, P0A72, P0A75, and/or P0E52 stored in the inverter system controller (SOBDMC). The Ford Diagnostic and Repair System (FDRS) may refer to this module as the "Secondary On-Board Control Module C". If the vehicle exhibits these conditions, replace the inverter system controller. Refer to Workshop Manual, Section 307-01B. For claiming, use causal part 7B012 and labor operations 12651D and 12651D58. NOTE: This article does not remove any RVC, Prior Approval or Warranty and Policy requirements for component replacement.
SSM 549392026-06-22. Service bulletin. Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. For claim
TSB 26-22102026-06-05. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM)
SSM 547972026-05-08. Service bulletin. Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation.
PT-26.12.1 Maverick2026-04-30. Over-the-air update. 25C69 Recall remedy - Updates the Secondary On-Board Diagnostic Module C to provide for release of the Integrated Park Module slider in the event a bind condition occurs allowing park to be engaged.
TSB 26-21702026-04-22. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit various electrical symptoms and/or a no crank/no start condition related to an intermittent 12v battery drain. This may be due to the software in the instrument panel cluster (IPC) and/or the air conditioning control module (ACCM).