Warranty extension SSPD9 Repair b

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Warranty extension
NHTSA id	11022773
Published by NHTSA	2025-09-05
Manufacturer's number	SSPD9 Repair b
Manufacturer's date	2025-08-26
Campaign id or software version	SSPD9
NHTSA component	ENGINE

NHTSA's summary

SSPD9 August 25, 2025 – Adding coverage for Towing Subject: Notification of Warranty Extension Program - Special Service Program (SSP) D9 2024 CX-90 and 2025 CX-70, SKYACTIV-G 2.5 PHEV – Water Heater Malfunction Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the water heater concern on certain MY2024 CX-90 PHEV and MY2025 CX-70 PHEV vehicles that are equipped with the suspected water heater. The warranty coverage for an applicable repair has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. Concern Outline: On certain subject vehicles, while warming up the cabin after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: 1) The heater does not work properly. 2) The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored in memory. - P0AA6:00 – High voltage insulation malfunction: Decrease in vehicle insulation resistance. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair the vehicle under this Special Service Program. SSPD9 – Water Heater Malfunction WARRANTY EXTENSION For certain 2024 CX-90 PHEV and 2025 CX-70 PHEV vehicles that are equipped with the suspected water heater, the warranty coverage for an applicable repair of the water heater has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. CONDITION OF CONCERN While warning up the cabin using the water heater after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: Heater performance may become poor: 1. The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored. 2. P0AA6:00 – High voltage insulation malfunction: Decrease in vehicle insulation resistance OWNER NOTIFICATION Mazda will notify all U.S. owners of the subject vehicles by first class mail no later than September 1, 2025. • Owners will be advised that they do not need to bring their vehicle to a dealer if it does not exhibit the affected conditions. • Owners will also be advised that any previous repair on the water heater due to concerns related to this SSP will be eligible for reimbursement if the repair was performed at the owner’s expense. Please refer the customer to the Owner Letter for reimbursement instructions. NO COVERAGE FOR BRANDED AND OTHER LIMITATIONS - EXCLUDED COVERAGE • Per Warranty policy 3.26 all limitations apply to this Warranty Extension. There is no coverage for total loss/insurance/salvage or rebuilt titles (W1). If you are unsure about the policy please contact the Warranty Department. REPAIR PROCEDURE If you receive customer complaints about the check engine light ON with P0AA6:00 with any of the symptoms mentioned above, verify the concerns and perform appropriate repair according to the Service Information Technical Service Bulletin (TSB) No. 07-006/24. Note: Please always refer to the latest version of TSB.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Trouble codes named

P0AA6

Vehicles listed
MAZDA CX-70 PLUG-IN HYBRID	2025 (the catalog's model; the bulletin names a series or trim of it)
MAZDA CX-90 PLUG-IN HYBRID	2024 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2024657	2024-10-31. Engine
24V815000	2024-10-31. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SA-061-26	2026-10-01. Service bulletin. DESCRIPTION Use this guide before ordering or replacing an AT component on applicable H3T vehicles. QUICK CHECKLIST BEFORE ORDERING Confirm the vehicle is a CX-90 (KK) or CX-70 (KJ) with H3T and is within the applicable market coverage. • In GEPC, identify the AT component part number for the vehicle. • Use the GEPC lookup tables below to determine whether the vehicle requires Table A or Table B parts. • Order the complete set of parts listed in the applicable table. DO NOT order the AT component by itself. • Check whether water hose removal is required for that GEPC part number. • Follow the applicable WSM repair procedure for AT component removal/installation, water hose removal, and oil hose/oil pipe installation in MGSS. • IMPORTANT: If only the AT component is ordered, required replacement parts will be missing, and the repair cannot be completed.
SA-059-26	2026-10-01. Service bulletin. This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-029/24 05/09/24 DESCRIPTION The CX-90 and CX-70 PHEV are equipped with two electric water pumps that look similar but have different part numbers. CAUTION: If the wrong water pump is ordered or they are reversed, DTC U019F could be set.
PF-26-04	2026-10-01. Other. SUBJECT: ORDERING REQUIREMENT FOR AT COMPONENTS FOR H3T (INLINE 6) Use this guide before ordering or replacing an AT component on applicable H3T vehicles. QUICK CHECKLIST BEFORE ORDERING • Confirm the vehicle is a CX-90 (KK) or CX-70 (KJ) with H3T and is within the applicable market coverage. • In GEPC, identify the AT component part number for the vehicle. • Use the GEPC lookup tables below to determine whether the vehicle requires Table A or Table B parts. • Order the complete set of parts listed in the applicable table. DO NOT order the AT component by itself. • Check whether water hose removal is required for that GEPC part number. • Follow the applicable WSM repair procedure for AT component removal/installation, water hose removal, and oil hose/oil pipe installation in MGSS. IMPORTANT: If only the AT component is ordered, required replacement parts will be missing, and the repair cannot be completed.
09-027-26	2026-10-01. Service bulletin. DESCRIPTION Some CX-70 and CX-90 PHEV vehicles may fail to start (enter READY mode) in cold weather, but the vehicle can often be started successfully on the next attempt. This may occur when leakage current between connector terminals causes the MAIN Relay to be falsely detected as ON. As a result, the Battery ECU may incorrectly determine the relay status, preventing READY mode activation and resulting in a no-start condition. One or more of the following DTCs may be stored: P0AB9, U0100, U0110, and U0115 and multiple warning lights may also turn on. This is caused by corrosion of the connector terminals on the 3002-411 connector in the luggage compartment from water. To eliminate this concern, urethane has been added around the connector to help prevent water from reaching the connector terminals. REPAIR PROCEDURE 1. Verify the customer concern. 2. Diagnose and repair the vehicle according to the following steps. NOTE: The following procedure uses a heat shrink tube with solder. (1) Connect wire to wire with heat shrink tube. (2) Form a loop at the end of wire to create a passage for the other wire.
SA-038-26a	2026-09-04. Service bulletin. This Service Alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-038/26 06/15/26 DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote functions inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
SA-058-26	2026-09-04. Service bulletin. This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-001/25 10/16/25, 05/15/25, 04/17/25 and 01/09/25 DESCRIPTION This Service Information is no longer valid and has been unpublished. Refer to: MSP66 - ENGINE WARNING ILLUMINATION WITH DTC P0DAB - 2024-2026 CX-90 AND 2025-2026 CX-70
SA-042-26	2026-07-03. Service bulletin. This Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out
SA-041-26	2026-07-03. Service bulletin. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
01-002-26a	2026-07-03. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 01-002/26 01/07/26 DESCRIPTION Some vehicles may exihibit a vibration in the accelerator pedal and steering wheel when accelerating during a sharp left-hand turn. An abnormal noise may also be heard from the footwell area. This may be caused by insufficient clearance between the engine mount stopper rubber and the engine mount bracket. Customer may state: Vehicle shudders/vibrates on left turns, most often when accelerating from a stop or entering a driveway. • They feel a pop or grind in the accelerator pedal when the vibration occurs. • They hear a rumbling or grinding noise, mainly from the right side, during the left-turn shudder. • NOTE: The condition does not occur at shallow steering angles or when the vehicle is stationary and the steering effort remains unchanged when the vibration and noise are present. REPAIR PROCEDURE 1. Verify the customer concern. NOTE: DO NOT use power tools in this procedure. Use hand tools only. 2. Disconnect the negative battery terminal using the procedure in [NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION]. 3. Remove the engine cover. b. Replace the stopper rubber (2) with a modified part.
MSP66 Warr b	2026-05-05. Service campaign. 2024-2026 CX-90 and 2025-2026 CX-70 Engine Warning Light Illumination with DTC P0DAB CONDITION OF CONCERN On certain subject vehicles, the engine warning light may illuminate, and the vehicle may be limited to engine-only operation due to activation of the fail-safe mode. Motor assist, i-stop and motor regenerative functions may be disabled, although the vehicle is safe to drive. The DTC P0DAB (Cell voltage variation malfunction) may be stored. Causal factor: Improper software in the Powertrain Control Module (PCM) and - MHB in MDARS display - BECM (Battery Energy Control Module). OUTLINE OF REPAIR Reprogram the PCM and MHB with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic And Repair Software (MDARS). Note: The TCM may or may not be reprogrammed, please see below for the claim type depending on whether the TCM was programmed or not programmed. All 2026MY vehicles do not require TCM programming. Older vehicles especially with recent software or campaign updates will already have the TCM at the latest software version and will not be programmed.