WenmarOpen by Wenmar Pro

Service bulletin 18-048-24

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11001223
Published by NHTSA2024-06-07
Manufacturer's number18-048-24
Manufacturer's date2024-05-09
NHTSA componentPOWER TRAIN
Manufacturer's systemPowertrain Control Module

NHTSA's summary

"Flash: Powertrain Control Module (PCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P02EE - Cylinder 1 Injector Circuit Performance (China Only). ● P02EF - Cylinder 2 Injector Circuit Performance (China Only). ● P02F0 - Cylinder 3 Injector Circuit Performance (China Only). ● P02F1 - Cylinder 4 Injector Circuit Performance (China Only). ● P2B95 - Cold Start Injection Pulse Performance. ● P152E - Engine Hood Switch Two Circuit High. ● P152F - Engine Hood Switch Two Engine Hood Switch One Correlation. Customers may also comment on the following: ● **""Performance Limited Service Fuel System"" message appears and then disappears after a few seconds/ minutes in the Instrument Panel Cluster (IPC) (All Markets).** This bulletin involves reprogramming the PCM with the latest available software."

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Trouble codes named

P02EE, P02EF, P02F0, P02F1, P152E, P152F, P2B95

Vehicles listed
JEEP WRANGLER2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
23V6410002023-09-18. POWER TRAIN:MANUAL TRANSMISSION
20230892023-02-23. Powertrain
23V1160002023-02-23. POWER TRAIN:CLUTCH ASSEMBLY
20226722022-11-23. Powertrain

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
S26210000042026-10-07. Service bulletin. The Customer May Complain About a Popping Noise, Grinding Noise, or an Intermittent No Reverse or Forward Transmission Engagement. The Tech May Find Damaged and/or Worn Transmission Output Shaft Splines (850RE Transmission Only)
21-041-26 REV. A2026-07-02. Service bulletin. Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set **one or more the following Diagnostic Troubles Code (DTCs): ● U0287-00 - Lost Communication With Transmission Fluid Pump Module 1.** ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode. This bulletin involves replacing the transmission oil pump.
18-008-26 REV. B2026-06-18. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating).** ● P08A6 – Gear Lever Position Sensor System – Multiple Sensor Correlation. (Manual Transmission Only) ● P152F – Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. Customers may also comment on one or more of the following: ● **The vehicle has a rough idle. ● The engine has a miss. ● Noisy valvetrain.** ● "Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection. (Manual Transmission Only) NOTE: Customers might experience wheel spin or slippage and the PCM could interpreted the wheel spin or slippage as slipping the clutch too much and to avoid clutch damage, the customer may see the message in the IPC. ● Vehicle is in limp home mode. Other software enhancements included: ● Engine oil pump in high pressure mode with cold engine oil to improve valvetrain component reliability. This bulletin involves reprogramming the PCM with the latest available software.
21-041-262026-05-20. Service bulletin. Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.
18-047-262026-04-22. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating). Customers may also comment on one or more of the following: ● The vehicle has a rough idle. ● The engine has a miss. ● Noisy valvetrain. This bulletin involves reprogramming the PCM with the latest available software.
S2621000003 REV.A2026-03-18. Service bulletin. The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S26030000012026-03-05. Service bulletin. A suspected leak may be noticed on the front or rear axle pinion seal.
S26210000032026-03-05. Service bulletin. Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
18-008-26 REV.A2026-03-05. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 – Gear Lever Position Sensor System – Multiple Sensor Correlation. (Manual Transmission Only) ● P152F – Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. Customers may also comment on one or more of the following: ● "Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection. (Manual Transmission Only) NOTE: Customers might experience wheel spin or slippage and the PCM could interpreted the wheel spin or slippage as slipping the clutch too much and to avoid clutch damage, the customer may see the message in the IPC. ● Vehicle is in limp home mode. Other software enhancements included: ● Engine oil pump in high pressure mode with cold engine oil to improve valvetrain component reliability. This bulletin involves reprogramming the PCM with the latest available software.
91006842025-10-29. Service bulletin. When servicing/replacing 68415437A$ Transmission, take care to not damage the PIM to P2 harness. Also, when reinstalling the harness, route the harness properly and secure it at all the retention points.