Service bulletin MC330224
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10252047 |
| Published by NHTSA | 2024-04-01 |
| Manufacturer's number | MC330224 |
| Manufacturer's date | 2024-03-18 |
| NHTSA component | POWER TRAIN |
NHTSA's summary
After close inspection of the manufacturing process, there is a weld seam at the hollow shaft and crown wheel connection in the rear drive that is not to specification in a few rear drives. Depending on riding habit, this can lead to slipping and loss of propulsion over time.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Transmission and driveline
| BMW R NINE T | 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021 |
|---|---|
| BMW R NINE T PURE | 2019, 2020, 2021 (the catalog's model; the bulletin names a series or trim of it) |
| BMW R NINE T RACER | 2018 (the catalog's model; the bulletin names a series or trim of it) |
| BMW R NINE T SCRAMBLER | 2018, 2019, 2020, 2021 (the catalog's model; the bulletin names a series or trim of it) |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| MC110521 | 2021-08-23. Service bulletin. During quality analysis, an issue was identified with a small group of sixteen (16) motorcycles that mayaffect crankshaft bearing wear. |
|---|---|
| B340517 | 2020-04-20. Service bulletin. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs. |
| MC62694734 | 2018-12-10. Service bulletin. Counterbalance shaft seal leaking. Faulty seal contact surface of the balance weight. |
| B123314 | 2018-12-10. Service bulletin. This Service Information bulletin supersedes SI 12 33 14 dated December 2015. SUBJECT Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat. |
| MC2300117 | 2018-11-26. Service bulletin. Customer complains about an operating failure on the left or right multifunction switch. |
| B270116 | 2018-11-13. Service bulletin. SERVICE ACTION: REPLACE THE DUST BOOT ON THE TRANSFER CASE. The dust boot (gaiter) for the front drive shaft at the transfer case may allow debris to enter the joint for the front driveshaft at the transfer case. The material of the dust boot may tear. |
| B340916 | 2018-11-05. Service bulletin. "POWER LOSS: CCM 350. Vehicle seems to have no power. CCM 350: ""It is possible to continue to drive. All-wheel drive system."" displayed One of the following fault memory entries may be stored: DSC_G11: o D36500 - Message fault (xDrive actuator information, ID: XDRV_ACT_INFO) - Timeout o D356E4 - Message fault (status of distribution of the longitudinal torque on the front axle rear axle, ID: ST_REPAT_XTRQ_FTAX_BAX) - Timeout Longitudinal Torque Distribution (LMV) control unit not operating" |
| B310112 | 2018-11-05. Service bulletin. CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle) |
| B240516 | 2018-11-05. Service bulletin. """TRANSMISSION OVERHEAT WARNING"" MESSAGE IS DISPLAYED. Check Control Message ""Transmission overheating warning"" is displayed. One or more of the following fault codes are stored in the transmission control unit (EGS): * 4209A1 - Temperature sensors: Hot operation 1 with possible adaptation of shift program * 4209A2 - Temperature sensors: Hot operation 2 with torque reduction * 4209A3 - Temperature sensors: Hot operation A faulty transmission oil cooler thermostat." |
| B170517 | 2018-11-05. Service bulletin. SERVICE ACTION: REPLACE THE MOUNT FOR THE TRANSMISSION OIL COOLER THERMOSTAT. There may be a rattling noise coming from the engine area at the transmission oil cooler thermostat or (on xDrive models only) the transmission oil cooler lines coming into contact with the left front output shaft. The bracket that holds the transmission oil cooler thermostat to the left front frame rail may be defective |