Service bulletin OTAPU0630-PFMNFO
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10251478 |
| Published by NHTSA | 2024-03-07 |
| Manufacturer's number | OTAPU0630-PFMNFO |
| Manufacturer's date | 2024-02-07 |
| NHTSA component | BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM |
NHTSA's summary
Software Update 23-PU0630-PFM-NFO for 2023 MY EXPEDITION vehicles is now available. Quality Improvements include: - Robustness action to Improve the Master Door Switch Pack loss of functionality.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Driver assistance, Electrical system, Backup camera
| FORD EXPEDITION | 2023 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 25V315000 | 2025-05-09. BACK OVER PREVENTION:SOFTWARE |
|---|
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| SSM 52134 | 2023-12-19. Service bulletin. Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition. |
|---|---|
| SSM 52044 | 2023-11-15. Service bulletin. Some 2022-2023 Expedition vehicles, built on or before 31-Aug-2023, may exhibit an inoperative approach detection or power door unlock command power running board extended deployment auto timer feature (delayed for 300 seconds without opening the door) when Extended is selected in the center display screen for the power running board AUTO mode. This may be due to various software parameters in the driver front seat module (DSM). To correct the condition, download and run the Driver Front Seat Module (DSM) Configuration app using the latest level of the Ford Diagnosis and Repair System (FDRS). For claiming use causal part number 14C708 and applicable labor times from Section 10 of the Service Labor Times Standard (SLTS) Manual. |
| SU5P1 Expedition | 2023-09-07. Service bulletin. Software Update 5 P1 for 2022-2023 Expedition Vehicles is now available. Quality improvements include: -Enables rear screen mirroring via vehicle wifi hotspot -Minimize time customer cannot enter the vehicle during future inhibit updates. |
| SSM 51776 | 2023-07-12. Service bulletin. Some 2021-2023 Mustang Mach-E/F-150, 2022-2023 Expedition/Navigator and 2023 Corsair vehicles may exhibit a Driver Monitoring Camera Blocked message and/or DTCs B115E:97, B15E1:97 and/or B15E2:97 stored in the driver status monitor camera module (CMR). These DTCs should be disregarded unless it is a DTC with a status byte 8F. Other status bytes should be disregarded as they may be caused by a camera obstruction such as driver position, aftermarket devices or dust on the camera. To clear the DTCs, remove anything obstructing the view of the camera and light emitting diodes (LEDs), place the steering wheel in the center position and close the driver door. Connect Ford Diagnosis and Repair System (FDRS) and clear the DTCs. Turn the ignition off and wait 10 seconds. Turn the ignition on and wait 1 minute. Perform the CMR self-test and reevaluate if DTCs persist. |