Service bulletin SSM 51677

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10237589
Published by NHTSA	2023-06-08
Manufacturer's number	SSM 51677
Manufacturer's date	2023-06-02
NHTSA component	POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE

NHTSA's summary

Some 2021-2023 Bronco vehicles may exhibit an inaccurate AAT reading with DTC P0072 stored in the powertrain control module (PCM). The Workshop Manual (WSM), Section 413-01 > pinpoint test (PPT) BC has been updated to address this concern. The AAT WSM updates include: improved diagnosis and testing, AAT sensor reset, and the AAT sensor interaction with climate control system and gateway module A (GWM).

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Transmission and driveline, Automatic transmission, Software, Transmission control module

Trouble codes named

P0072

Vehicles listed
FORD BRONCO	2021, 2022, 2023

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
26V236000	2026-04-14. POWER TRAIN:AUTOMATIC TRANSMISSION
23V546000	2023-08-03. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:PARK PAWL
23V070000	2023-02-10. POWER TRAIN:AUTOMATIC TRANSMISSION

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 52364	2024-04-04. Service bulletin. 2021-2023 Bronco vehicles built on or before 9-Jul-2023 may have new version software in their driver door module (DDM) and passenger door module (PDM) that contains noticeable enhancements to the window short drop operation. This software level can be identified in the DDM and PDM as Software Part Number MU5T-14C064-CR or later. This software was released via a software update delivered over-the-air (OTA) starting in September 2023 if the vehicle's connectivity was enabled in the vehicle settings. Vehicles with this new software will exhibit a short drop event to all door windows anytime the vehicle is unlocked using the remote keyless entry (RKE), accessory keyless entry keypad, or the interior door unlock switch. The short drop function will return to the UP position when a lock input is received from these same inputs. For vehicles equipped with passive entry, a short drop event will not activate when a door is unlocked by placing a hand on an exterior door handle. 2023-2024 Bronco vehicles built on and after 10-Jul-2023 received this software from the factory.
SSM 52354	2024-04-04. Service bulletin. Some 2023 Bronco vehicles may exhibit diagnostic trouble code (DTC) U2101 stored in accessory protocol interface module (APIM) and/or telematics control unit (TCU) after TCU module programming with no additional symptoms present. This may be due to the TCU configuration. To correct the concern, download and run the TCU-Telematics Control Unit (TCU) Module Configuration application using Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14F546 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52345	2024-03-20. Service bulletin. Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52342	2024-03-20. Service bulletin. Some 2022-2024 Broncos Raptors built on and before 13-Feb-2024 and 2021-2024 Broncos equipped with a 2.3L EcoBoost engine may exhibit an illuminated MIL with ignition system DTC(s) P0352, P0353, P0354, P0355, P0357, P2303, P2306, P2309, P2312, P2318, P2304, P2307, P2310, P2313, P2319, and/or P2322 set in the powertrain control module (PCM). This may be due to incorrect cylinder to DTC mapping within the PCM. This means the DTCs listed may set against the incorrect cylinder. Even though the cylinder to DTC mapping is incorrect in the PCM, the presence of these DTCs means that a real ignition system concern is present that requires diagnosis and repair. Prior to performing a pinpoint test for one of the listed DTCs, it will be necessary to identify the correct cylinder that has the issue. Do this by using the Ford diagnosis and repair system (FDRS) to perform a cylinder power balance test. If the results show two cylinders dropping out, begin diagnosing the ignition system components for the cylinder that is dropping out and not setting an ignition related DTC. Due to the incorrect cylinder to DTC mapping
23B21 S1	2024-03-05. Service bulletin. Certain 2023 Model Year F-150 and Bronco Vehicles - Gateway Module Programing
SSM 52197	2024-01-30. Service bulletin. Some 2021-2024 Bronco vehicles equipped with 4x4 with part time engagement and built on or before 12-Jan-2024 may exhibit a condition of the vehicle being stuck in neutral tow mode. This may be due to a concern with the all-wheel drive (AWD) module software. Make sure the proper procedure is being followed to exit neutral tow mode by referring to the Owner's Manual > Towing Your Vehicle > Recreationally Towing Your Vehicle. Make sure the vehicle's battery is fully charged and then diagnose all diagnostic trouble codes (DTCs) in the AWD module. Refer to Workshop Manual (WSM), Section 307-07A. If diagnostics do not resolve the concern or there are no DTCs present in the AWD module, reprogram the AWD module using the latest software level of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. Refer to the appropriate section of the WSM. Once the repair is complete, verify the vehicle's ability to successfully enter and exit neutral tow mode by cycling the vehicle in and out of neutral tow mode a minimum of two times, allowing the vehicle to enter sleep mode (key-off for at least 5 minutes) be
OTAPU0813DORUP2	2023-12-07. Service bulletin. Software Update PU0813-DOR-UP2 for 2023 BRONCO vehicles is now available. Quality improvements include: - Updated strategy to learn hard stop window travel at top and bottom to reduce unintended window bounce back and prevent loss of one touch function.
OTA SU6 P1BRONCO	2023-12-07. Service bulletin. Software Update SU6 P1 for 2023 BRONCO vehicles is now available. Quality improvements include: - Prevent unintended fuel level MIL after future OTA updates - Enhanced electronic brake booster to improve the braking experience when vehicle is flat towed.
SSM 52036	2023-11-09. Service bulletin. Some 2021-2023 Bronco vehicles equipped with 4x4 with part time engagement may exhibit a condition of the vehicle being stuck in neutral tow mode. This may be due to a concern with the all-wheel drive (AWD) module. Make sure the proper procedure is being followed to exit neutral tow mode by referring to the Owner's Manual > Towing Your Vehicle > Recreationally Towing Your Vehicle. Make sure the vehicle's battery is fully charged and then diagnose all diagnostic trouble codes (DTCs) in the AWD module. Refer to Workshop Manual (WSM), Section 307-07A. If diagnostics do not resolve the concern or there are no DTCs present in the AWD module, replace the transfer case and the AWD module. Refer to the appropriate section of the WSM. Once repair is complete, verify the vehicle's ability to successfully enter and exit neutral tow mode by cycling the vehicle in and out of neutral tow mode a minimum of two times, allowing the vehicle to enter sleep mode (key-off for at least 5 minutes) between each cycle. Inform customers that Ford is currently working on a software update to address this condition without a need
SSM 51961	2023-11-03. Service bulletin. Some 2021-2023 Bronco vehicles may exhibit an illuminated MIL with DTCs P0096 and/or P007B in the powertrain control module (PCM), which may be more prevalent in high ambient air temperatures. For vehicles that meet this criateria, inspect the front of the vehicle for the presence of an aftermarket bumper and/or accessories which may restrict air flow to the charge air cooler and surrounding sensors. Remove the aftermarket accessory and return the vehicle to stock and reevaluate. If the concern returns with the stock bumper/accessories removed, proceed to normal Workshop Manual diagnostics.